Abstract
A method involving multi-exposure with low-power is presented to fabricate an SU-8 mold based on a digital micromirror device (DMD) maskless lithography with an LED source at a wavelength of 405 nm. The SU-8 mold is used for the fabrication of a PDMS concentration gradient generator (CGG). During a one-time exposure, it is easy to over-expose at the top and under-expose at the bottom of a thick SU-8, which then forms a T-shaped structure. This is more obvious for high-absorption coefficients such as 365 nm. We found that by taking advantage of the partially absorbed and partially transmissive characteristics of the 405-nm wavelength, multi-exposure can form an effective photochemical reaction channel in SU-8 and can solve the problem mentioned above. However, excessive exposure will cause the linewidth to increase, therefore, it is necessary to find a tradeoff for the number of multi-exposure times. For a 55-µm thick SU-8, the tradeoff threshold is found to be 25. Three types of SU-8 CGG molds were fabricated at this threshold. The results indicate that the actual profile of the SU-8 mold shows good agreement with the design profile without any T-shaped structures.
Similar content being viewed by others
References
Fang, X., Chen, H., Xu, L., Jiang, X., Wu, W. & Kong, J. A portable and integrated nucleic acid amplification microfluidic chip for identifying bacteria. Lab Chip 12, 1495–1499 (2012).
Guo, M.T., Rotem, A., Heyman, J.A. & Weitz, D.A. Droplet microfluidics for high-throughput biological assays. Lab Chip 12, 2146–2155 (2012).
Dittrich, P.S. & Manz, A.A. Lab-on-a-chip: microfluidics in drug discovery. Nat. Rev. Drug Discovery 5, 210–218 (2006).
Gao, S., Tung, W.T., Wong, D.S.H., Bian, L. & Zhang, A.P. Direct optical micropatterning of poly (dimethylsiloxane) for microfluidic devices. J. Micromech. Microeng. 28, 095011 (2018).
Lin, Y. Numerical characterization of simple three-dimensional chaotic micromixers. Chem. Eng. J. 277 303–311 (2015).
Chen, X., Li, T. & Hu, Z. A novel research on serpentine microchannels of passtive micromixers. Microsyst. Technol. 23 2649–2656 (2017).
McDonald J.C. & Whitesides, G.M. Poly(dimethylsiloxane) as a material for fabricating microfluidic devices. Acc. Chem. Res. 35, 491–499 (2002).
Huang, B.B., Yin, M.J., Zhang, A.P. & Ye, X.S. On-chip microfabrication of thermally controllable PNIPAAm microvalves by using optical maskless stereolithography. Sens. Actuators A 247, 397–402 (2016).
Wu, J., Guo, X., Zhang, A.P. & Tam, H.Y. Rapid 3D µ-printing of polymer optical whispering-gallery mode resonators. Opt. Express 23, 29708–29714 (2015).
Yin, M.J., Yao, M., Gao, S., Zhang, A.P., Tam, H.Y. & Wai, P.K.A. Rapid 3D patterning of poly (acrylic acid) ionic hydrogel for miniature pH sensors. Adv. Mater. 28, 1394–1399 (2016).
Yin, M.J., Huang, B.B., Gao, S.R., Zhang, A.P. & Ye, X.S. Optical fiber LPG biosensor integrated microfluidic chip for ultrasensive glucose detection. Biomed. Opt. Express 7, 2067–2077 (2016).
Wang, J., Yao, M., Hu, C.Z., Zhang, A.P., Shen, Y. H., Tam H.Y. & Wai, P.K.A. Optofluidic tunable mode-locked fiber laser using a long-period grating integrated microfluidic chip. Opt. Lett. 42, 1117–1120 (2017).
Yang, B., Zhou, J.Y., Chen, Q.M., Lei, L. & Wen, K.H. Fabrication of hexagonal compound eye microlens array using DMD-based lithography with dose modulation. Opt. Express 26 28927–28937 (2018).
Mack, C.A., Matsuzawa, T., Sekiguchi, A. & Minami, Y. Resist metrology for lithography simulation, part I: exposure parameter measurements. Proc. SPIE Metrology, Inspection, and Process Control for Microlithography X, 2725, 34–48 (1996).
Xu, B.J., Jin, Q.H. & Zhao, J.L. Fabrication and application of multilayer SU-8 based micro dispensing array chip. Journal of functional materials and devices 12, 377–382 (2006).
Zhao, L., Zhang, B.Z., Duan, J.P. & Cui, J.L. The design and manufacture of micro cantilever based on thick photoresist. Science Technology and Engineering 15, 128–131 (2015).
Ghosh, S. & Ananthasuresh, G.K. Single-photon-multi-layer-interference lithography for high-aspect-ratio and three-dimensional SU-8 micro-/nanostructures. Sci. Rep. 6, 18428 (2016).
Gou, M., Qu, X., Zhu, W., Xiang, M., Yang, J., Zhang, K., Wei, Y. & Chen, S. Bio-inspired detoxification using 3d-printed hydrogel nanocomposites. Nat. Commun. 5, 3774 (2014).
Hribar, K.C., Finlay, D., Ma, X., Qu, X., Ondeck, M.G., Chung, P.H., Zanella, F., Engler, A.J., Sheikh, F., Vuori, K. & Chen, S.C. Nonlinear 3D projection printing of concave hydrogel microstructures for long-term multicellular spheroid and embryoid body culture. Lab Chip, 15, 2412–2418 (2015).
Zhang, A.P., Qu, X., Soman, P., Hribar, K.C., Lee, J. W., Chen, S. & He, S. Rapid fabrication of complex 3D extracellular microenvironments by dynamic optical projection stereolithography. Adv. Mater. 24, 4266–4270 (2012).
Luo, N.N., Xu, G.Y., Zhang, Z.M. & Zhang, W.W. Reduction of buried microstructure diffraction in fabricating curved microstructure by multiple exposure method. Opt. Express, 26, 31085–31093 (2018).
Ryoo, H., Kang, D.W. & Hahn, J.W. Analysis of the line pattern width and exposure efficiency in maskless lithography using a digital micromirror device. Microelectron. Eng. 88, 3145–3149 (2011).
Sensu, Y., Sekiugehi, A., Morinad, S. & Hond, N. Porfile simulation of SU-8 thick film resist. Proc. SPIE, Advances in Resist Technology and Processing XXII 5753, 1170–1185 (2005).
Leeds, A.R., Van Keuren, E.R., Dusrt, M.E., Schnelder, T.W., Currie, J.F. & Paranjape, M. Integration of microfluidic and microoptical elements using a single-mask Photolithographic step. Sens. Actuators, A 115, 571–580 (2004).
Zhang, J.Y., Chen, D., Zhu, J., Li, J.H., Fang, H.B. & Yang, B. Process study of high-aspect-ratio ultrathick SU-8 microstructures, Journal of Functional materials and devices (in Chinese) 11, 251–254 (2005).
Yoshihisa, S., Atsushi, S. & Yoshiyuki, K. Profile simulation of SU-8 thick film resist. J. Photopolym. Sci. Technol. 18, 125–132 (2005).
Dill, F.H., Hornberger, W.P., Hauge, P.S. & Shaw, J.M. Characterization of positive photoresist, IEEE. Trans. Electron Devices 22, 445–452 (1975).
Acknowledgements
This work was funded by Research and Development planning project in key areas of Guangdong Province (grant no. 2020B090924 001) and Guangzhou Science and Technology planning project (202002030210). The authors would like to thank the Analysis and Test center of GDUT for use of its LSCM facility and thank Editage [www.editage.cn] for English language polishing.
Author information
Authors and Affiliations
Corresponding author
Additional information
Conflict of Interests
The authors declare no competing financial interests.
Rights and permissions
About this article
Cite this article
Chen, QM., Zhou, JY., Hu, YM. et al. Tradeoff Control of Multi-exposure Lithography for SU-8 Photochemical Reaction Channel Formation. BioChip J 14, 369–380 (2020). https://doi.org/10.1007/s13206-020-4405-y
Received:
Accepted:
Published:
Issue Date:
DOI: https://doi.org/10.1007/s13206-020-4405-y