Abstract
With automobile numbers continuing to increase, competition among manufacturers of brake pads is also increasing along with the search for additives to serve as alternatives to the materials presently being used. In addition to the cost of the additives used, another important consideration in choosing materials is that they should be safe for the environment and human health. This study investigated the effect on braking performance of brake pads produced using walnut shell powder as a natural additive material. Two different types of brake pad samples were produced using 3.5 (2A) and 7% (2B) walnut shell dust in the contents. A commercial Clio brake tip was used as the reference (CO). The produced brake pads were subjected to thermal conductivity, friction wear, density, hardness and water and oil absorption tests and microstructure analysis. A Chase type device was used for wear friction tests, and the results were obtained according to SAE-J661(Brake Lining Quality Test Procedure) standards. The experimental data were compared with those of the commercial brake pads, and the performances of the natural additive brake pads were evaluated. The addition of walnut shell was shown to be compatible within the composition and exhibited a positive effect on the friction coefficient.
Similar content being viewed by others
References
Rashid, B., Leman, Z., Jawaid, M., Ghazali, M., Ishak, M., Abdelgnei, M.: Dry sliding wear behavior of untreated and treated sugar palm fiber filled phenolic composites using factorial technique. Wear. 380, 26–35 (2017)
Kchaou, M., Lazim, A.M., Hamid, M.A., Bakar, A.A.: Experimental studies of friction-induced brake squeal: influence of environmental sand particles in the interface brake pad-disc. Tribol. Int. 110, 307–317 (2017)
Menapace, C., Leonardi, M., Perricone, G., Bortolotti, M., Straffelini, G., Gialanella, S.: Pin-on-disc study of brake friction materials with ball-milled nanostructured components. Mater. Des. 115, 287–298 (2017)
Hong, U.S., Jung, S.L., Cho, K.H., Cho, M.H., Kim, S.J., Jang, H.: Wear mechanism of multiphase friction materials with different phenolic resin matrices. Wear. 266(7–8), 739–744 (2009). https://doi.org/10.1016/j.wear.2008.08.008
Weintraub, M.: Brake additives consultant. Private communication 107–127 (1998).
Zaharudin, A., Talib, R., Berhan, M., Budin, S., Aziurah, M.: Taguchi method for optimising the manufacturing parameters of friction materials. Proceedings of Regional Tribology Conference 2011: RTC2011, 246 (2011)
Eriksson, M.: Friction and contact phenomena of disc brakes related to squeal. Citeseer (2000)
Aigbodion, V.S., Akadike, U., Hassan, S.B., Asuke, F., Agunsoye, J.O.: Development of asbestos -free brake pad using bagasse. Trib Ind. 32(1), 12–18 (2010)
Jacko, M.G., Tsang, P.H.S., Rhee, S.K.: Automotive friction materials evolution during the past decade. Wear. 100(1–3), 503–515 (1984). https://doi.org/10.1016/0043-1648(84)90029-2
Blau, P.J.: Compositions, Functions, and Testing of Friction Brake Materials and their Additives. Oak Ridge National Lab., Oak Ridge (2001)
Idris, U., Aigbodion, V., Abubakar, I., Nwoye, C.: Eco-friendly asbestos free brake-pad: using banana peels. J K Saud Un Eng Sci 27(2), 185–192 (2015)
Lazim, A.M., Kchaou, M., Hamid, M.A., Bakar, A.A.: Squealing characteristics of worn brake pads due to silica sand embedment into their friction layers. Wear. 358, 123–136 (2016)
Aku, S., Yawas, D., Madakson, P., Amaren, S.: Characterization of periwinkle shell as asbestos-free brake pad materials. Pac. J. Sci. Technol. 13(2), 57–63 (2012)
A. O. A. Ibhadode, Dagwa, i.M.: Development of Asbestos-Free Friction Lining Material from Palm Kernel Shell. J. of the Braz. Soc. of Mech. Sci. & Eng. xxx(2), 166–173 (2008)
Ghazali, C.M.R., Kamarudin, H., Shamsul, J., Abdullah, M., Rafiza, A.: Mechanical properties and wear behavior of brake pads produced from palm slag. Adv Mat Res 341(26), 26–30 (2012)
Qi, S., Fu, Z., Yun, R., Jiang, S., Zheng, X., Lu, Y., Matejka, V., Kukutschova, J., Peknikova, V., Prikasky, M.: Effects of walnut shells on friction and wear performance of eco-friendly brake friction composites. P I Mech Eng J-J-Eng. 228(5), 511–520 (2014). https://doi.org/10.1177/1350650113517112
El-Tayeb, N.S.M., Liew, K.W.: On the dry and wet sliding performance of potentially new frictional brake pad materials for automotive industry. Wear. 266(1–2), 275–287 (2009). https://doi.org/10.1016/j.wear.2008.07.003
Solomon, D.G., Berhan, M.N.: Characterization of Friction Material Formulations for Brake Pads. In: World Congress on Engineering, pp. 2-4 (2007)
Mutlu, I., Oner, C., Findik, F.: Boric acid effect in phenolic composites on tribological properties in brake linings. Mater. Des. 28(2), 480–487 (2007). https://doi.org/10.1016/j.matdes.2005.09.002
Ademoh, N.A., Olabisi, A.I.: Development and evaluation of maize husks (asbestos-free) based brake pad. Ind Eng Let 5(2), 67–80 (2015).
Saffar, A., Shojaei, A.: Effect of rubber component on the performance of brake friction materials. Wear. 274-275, 286–297 (2012). https://doi.org/10.1016/j.wear.2011.09.012
Prabhu, T.R.: Effects of solid lubricants, load, and sliding speed on the tribological behavior of silica reinforced composites using design of experiments. Mater. Des. 77, 149–160 (2015). https://doi.org/10.1016/j.matdes.2015.03.059
Ram Prabhu, T., Varma, V.K., Vedantam, S.: Tribological and mechanical behavior of multilayer cu/SiC + gr hybrid composites for brake friction material applications. Wear. 317(1–2), 201–212 (2014). https://doi.org/10.1016/j.wear.2014.06.006
570–98, A.D.: Standard test method for water absorption of plastics. In. (1999)
ASTM: standard test method for acetone extraction of phenolic molded or laminated products. In: ASTM D 494–04. pp. 1–3. ASTM International, US (2004)
J661, S.: Brake lining quality test procedure. In, vol. J661. (2012)
Dadkar, N., Tomar, B.S., Satapathy, B.K.: Evaluation of flyash-filled and aramid fibre reinforced hybrid polymer matrix composites (PMC) for friction braking applications. Mater. Des. 30(10), 4369–4376 (2009). https://doi.org/10.1016/j.matdes.2009.04.007
Lu, Y.: A combinatorial approach for automotive friction materials: effects of ingredients on friction performance. Compos. Sci. Technol. 66(3), 591–598 (2006)
Ertan, R., Yavuz, N.: An experimental study on the effects of manufacturing parameters on the tribological properties of brake lining materials. Wear. 268(11–12), 1524–1532 (2010). https://doi.org/10.1016/j.wear.2010.02.026
G. Akıncıoğlu, H.Ö., I. Uygur, S. Akıncıoğlu: Determination of Friction-Wear Performance and Properties of Eco-Friendly Brake Pads Reinforced with Hazelnut Shell and Boron Dusts. Arab J Sci Eng 43(9), 4727-4737 (2018).
Singh, T., Patnaik, A., Chauhan, R.: Optimization of tribological properties of cement kiln dust-filled brake pad using grey relation analysis. Mater. Des. 89, 1335–1342 (2016). https://doi.org/10.1016/j.matdes.2015.10.045
Yawas, D.S., Aku, S.Y., Amaren, S.G.: Morphology and properties of periwinkle shell asbestos-free brake pad. J K Saud U Eng Sci 28(1), 103–109 (2016). https://doi.org/10.1016/j.jksues.2013.11.002
Bijwe, J., Kumar, M.: Optimization of steel wool contents in non-asbestos organic (NAO) friction composites for best combination of thermal conductivity and tribo-performance. Wear. 263(7–12), 1243–1248 (2007). https://doi.org/10.1016/j.wear.2007.01.125
Blau, P.J., McLaughlin, J.C.: Effects of water films and sliding speed on the frictional behavior of truck disc brake materials. Tribol. Int. 36(10), 709–715 (2003). https://doi.org/10.1016/S0301-679X(03)00026-4
Ghazi, A., Chandra, K., Misra, P.: Development and characterization of Fe-based friction material made by hot powder preform forging for low duty applications. J. Miner. Mater. Charact. Eng. 10(13), 1205–1212 (2011)
Stadler, Z., Krnel, K., Kosmac, T.: Friction behavior of sintered metallic brake pads on a C/C–SiC composite brake disc. J. Eur. Ceram. Soc. 27(2–3), 1411–1417 (2007). https://doi.org/10.1016/j.jeurceramsoc.2006.04.032
Ji, Z., Jin, H., Luo, W., Cheng, F., Chen, Y., Ren, Y., Wu, Y., Hou, S.: The effect of crystallinity of potassium titanate whisker on the tribological behavior of NAO friction materials. Tribol. Int. 107, 213–220 (2017)
Erikssona, M., Lordb, J.: Jacobson, S.: Wear and contact conditions of brake pads: dynamical in situ studies of pad on glass. Wear. 249, 272–278 (2001)
Martinez, A.M., Echeberria, J.: Towards a better understanding of the reaction between metal powders and the solid lubricant Sb2S3 in a low-metallic brake pad at high temperature. Wear. 348-349, 27–42 (2016). https://doi.org/10.1016/j.wear.2015.11.014
Jaafar, T.R., Selamat, M.S., Kasiran, R.: Selection of Best Formulation for Semi-Metallic Brake Friction Materials Development. In: Powder Metallurgy. InTech (2012)
Funding
This study was supported by the Scientific Research Project Unit of Duzce University (DÜBAP-2015/72). The authors also thank Balatacılar Cooperation Inc. for their contributions.
Author information
Authors and Affiliations
Corresponding author
Additional information
Publisher’s note
Springer Nature remains neutral with regard to jurisdictional claims in published maps and institutional affiliations.
Rights and permissions
About this article
Cite this article
Akıncıoğlu, G., Akıncıoğlu, S., Öktem, H. et al. Wear response of non-asbestos brake pad composites reinforced with walnut shell dust. J Aust Ceram Soc 56, 1061–1072 (2020). https://doi.org/10.1007/s41779-020-00452-6
Received:
Revised:
Accepted:
Published:
Issue Date:
DOI: https://doi.org/10.1007/s41779-020-00452-6