Abstract
The results of experimental studying glue-mechanical shaft–sleeve joints using anaerobic sealants are presented. Quantitative estimates of the quality of the surface layers are obtained for mating parts, which allows assessing the values of the waviness of shaft and sleeve surfaces. A technique for determining the waviness of cylindrical joints is described. The effect of the press fit on mechanical strength of the shaft–sleeve joint is established depending on the properties of an anaerobic sealant.
Similar content being viewed by others
REFERENCES
D. A. Aronovich, “Modification of the properties of anaerobic adhesives. Review of current advances,” Plast. Massy., Nos. 7–8, 9–15 (2019).
D. A. Aronovich, A. F. Mupokh, A. P. Sineokov, and Z. S. Khamidulova, “Investigation of the properties of anaerobic-curing adhesives in cylindrical joints,” Klei, Germetiki, Tekhnol., No. 6, 2–6 (2008).
V. A. Zorin, N. I. Baurova, and A. M. Shakurova, “Investigation of the structure of an encapsulated anaerobic adhesive,” Polym. Sci., Ser. D 7 (4), 303–305 (2014).
I. I. Voyachek, “Selective hardening of pressure coupled joints in assembly with anaerobic materials,” Izv. Vyssh. Uchebn. Zaved., Povolzh. Reg., No. 2, 192–204 (2015).
D. V. Knyazev, “Features of the assembly of cylindrical joints with pressure coupling by the combined heat-glue method,” Izv. Mosk. Gos. Tekh. Univ. MAMI, No. 2, 270–274 (2008).
A. P. Petrova and G. V. Malysheva, Adhesives, Adhesive Binders, and Adhesive Prepregs: Handbook, Ed. by E. N. Kablov (VIAM, Moscow, 2017) [in Russian].
G. V. Malysheva and O. A. Ryakhovskii, “Calculation of force and tightening torque of threaded joints assembled using anaerobic material,” Polym. Sci., Ser. D 7 (4), 306–309 (2014).
O. A. Ryakhovskii, “A new method of sealing the joint of flanges of housings at high internal pressure,” Izv. Vyssh. Uchebn. Zaved., No. 5, 29–33 (2013).
E. V. Ryzhov, Fundamentals of Calculating the Butt Surfaces of Machine Parts for Contact Stiffness (Mashgiz, Moscow, 1962) [in Russian].
A. V. Borodin and I. L. Ryazantseva, “Effect of modification of mating surfaces on the load-bearing capacity of preloaded joints,” Izv. Transsiba, No. 1, 15–20 (2010).
N. V. Bodrykh and G. V. Malysheva, “Repair of starter storage batteries,” Polym. Sci., Ser. D 3 (1), 70–73 (2010).
Author information
Authors and Affiliations
Corresponding author
Additional information
Translated by V. Vetrov
Rights and permissions
About this article
Cite this article
Lyubchenko, M.A., Ryakhovskii, O.A., Vorob’ev, A.N. et al. Estimating Loading Capacity in Fit-Pressed Adhesive Joints. Polym. Sci. Ser. D 14, 345–349 (2021). https://doi.org/10.1134/S1995421221030199
Received:
Revised:
Accepted:
Published:
Issue Date:
DOI: https://doi.org/10.1134/S1995421221030199