Abstract
An approach to determining the optimal tightening of screws is proposed for joints under variable load. In this approach, the optimal tightening force corresponds to equal risk of uncoupling and fatigue failure.
This is a preview of subscription content, log in via an institution to check access.
Similar content being viewed by others
REFERENCES
Andrienko, L.A., Baikov, B.A., and Zakharov, M.N., Detali mashin (Machine Parts), Moscow: Mosk. Gos. Tekh. Univ. im. N.E. Baumana, 2014.
Birger, I.A. and Iosilevich, G.B., Rez’bovye i flantsevye soedineniya (The Thread and Flanged Junctions), Moscow: Mashinostroenie, 1990.
Ito, Y., Modular Design for Machine Tools, New York: McGraw Hill, 2008.
Ivanov, A.S. and Murkin, S.V., Screw tightening in dynamically loaded threaded joints, Russ. Eng. Res., 2016, vol. 36, no. 10, pp. 809–810.
Ito, Y., Toyoda, J., and Nagata, S., Interface pressure distribution in a bolt-flange assembly, J. Mech. Des., 1979, vol. 101, pp. 330–337.
Ito, Y., Murakami, Y., and Itoh, S., Interface pressure distribution in single bolt-flange assembly—Development of a measuring equipment for two dimensional interface pressure distribution and a few measured results, Trans. JSME, 1984, vol. 50, no. 458, pp. 1816–1824.
Ito, Y., A contribution to the effective range of the preload on a bolted joint, Proc. Fourteenth Int. Machine Tool Design and Research Conf., New York: Springer-Verlag, 1974, pp. 503–507.
Ivanov, A.S. and Murkin, S.V., Raschet i proektirovanie rez’bovykh soedninenii privodov (Calculation and Design of Drive Treaded Joints), Moscow: Innovatsionnoe Mashinostroenie, 2015.
Reshetov, D.N. and Levina, Z.M., Calculation of machines for contact rigidity, Stanki Instrum., 1951, no. 1.
Murkin, S.V., Ivanov, A.S., Ermolaev, M.M., and Rudnev, S.K., Position of the skew axis of a threaded joint under the action of a tipping torque, Russ. Eng. Res., 2016, vol. 36, no. 1, pp. 16–19.
Ivanov, A.S. and Izmailov, V.V., Calculation of contact deformation in machine engineering, Trenie Smazka Mash. Mekh., 2006, no. 8, pp. 3–10.
Zakharov, M.N., Prochnostnaya nadezhnost’ oborudovaniya (Strength Reliability of the Equipment), Moscow: Mosk. Gos. Tekh. Univ. im. N.E. Baumana, 2011.
Serensen, S.V. and Kogaev, V.P., Nesushchaya sposobnost’ i raschety detalei mashin na prochnost’ (Bearing Capacity and Strength Calculation of Machine Parts), Moscow: Mashinostroenie, 1975.
Peterson, R.E., Stress-Concentration Factors, New York: Wiley, 1974.
Author information
Authors and Affiliations
Corresponding author
Additional information
Translated by B. Gilbert
About this article
Cite this article
Zakharov, M.N., Kuts, M.S. Bolt Tightening with Equal Risk of Uncoupling and Fatigue Failure. Russ. Engin. Res. 40, 11–14 (2020). https://doi.org/10.3103/S1068798X20010244
Received:
Revised:
Accepted:
Published:
Issue Date:
DOI: https://doi.org/10.3103/S1068798X20010244