Abstract
Basalt fabric with manufacturer-made silane sizing was additionally treated by propane-butane enriched atmospheric pressure nitrogen plasma for 15 and 30 s. The wetting improvement of treated fabric was demonstrated by faster soaking of K2CO3 solution. FTIR and XPS analyses confirmed the presence of new nitrogen-containing chemical groups. The impact on adhesion was investigated via a shear strength test of basalt fabric inlay between two beech wooden boards. A short 15 s long treatment led to almost 50% increase in melamine-urea formaldehyde (MUF), polyvinyl acetate (PVAC) and epoxy resin bond strength. Phenol-resorcinol formaldehyde (PRF) needed longer treatment to achieve a bond strength of 11.2 MPa. Only the polyurethane (PUR) showed reduced adhesion to plasma-treated fibers. However, from all tested resins, PUR exhibited the highest bond strength (15.7 MPa) with untreated basalt fabric. The SEM of tested specimens confirmed the changes in the mechanical adherence of resins to plasma treated fibers. Based on these results, PRF and PUR seem to be the most suitable polymers for basalt fibers reinforcement of structural wood-based materials.
Similar content being viewed by others
References
Ammann S, Niemz P (2015) Mixed-mode fracture toughness of bond lines of PRF and PUR adhesives in European beech wood. Holzforschung 69:415–420. https://doi.org/10.1515/hf-2014-0096
Botev M, Betchev H, Bikiaris D, Panayiotou C (1999) Mechanical properties and viscoelastic behavior of basalt fiber-reinforced polypropylene. J Appl Polym Sci 74:523–531. https://doi.org/10.1002/(SICI)1097-4628(19991017)74:3%3c523::AID-APP7%3e3.0.CO;2-R
Brabec M, Lagaňa R, Milch J, Tippner J, Sebera V (2017) Utilization of digital image correlation in determining of both longitudinal shear moduli of wood at single torsion test. Wood Sci Technol 51:29–45. https://doi.org/10.1007/s00226-016-0848-7
Brunetti M, Christovasilis IP, Micheloni M, Nocetti M, Pizzo B (2019) Production feasibility and performance of carbon fibre reinforced glulam beams manufactured with polyurethane adhesive. Compos Part B Eng 156:212–219. https://doi.org/10.1016/j.compositesb.2018.08.075
Cech V, Prikryl R, Balkova R, Grycova A, Vanek J (2002) Plasma surface treatment and modification of glass fibers. Compos Part A Appl Sci Manuf 33:1367–1372. https://doi.org/10.1016/S1359-835X(02)00149-5
Czigány T, Deák T, Tamás P (2008) Discontinuous basalt and glass fiber reinforced PP composites from textile prefabricates: effects of interfacial modification on the mechanical performance. Compos Interfaces 15:697–707. https://doi.org/10.1163/156855408786778302
Davies P, Casari P, Carlsson LA (2005) Influence of fibre volume fraction on mode II interlaminar fracture toughness of glass/epoxy using the 4ENF specimen. Compos Sci Technol 65:295–300. https://doi.org/10.1016/j.compscitech.2004.07.014
de Moura MFSF, Campilho RDSG, Amaro AM, Reis PNB (2010) Interlaminar and intralaminar fracture characterization of composites under mode I loading. Compos Struct 92:144–149. https://doi.org/10.1016/j.compstruct.2009.07.012
Deak T, Czigany T, Tamas P, Nemeth C (2010) Enhancement of interfacial properties of basalt fiber reinforced nylon 6 matrix composites with silane coupling agents. Express Polym Lett 4:590–598. https://doi.org/10.3144/expresspolymlett.2010.74
Dhand V, Mittal G, Rhee KY, Park S-J, Hui D (2015) A short review on basalt fiber reinforced polymer composites. Compos Part B Eng 73:166–180. https://doi.org/10.1016/j.compositesb.2014.12.011
Dhé P (1922) Filament composed of basalt. US 1,438,428
Dvořáková H, Čech J, Stupavská M, Prokeš L, Jurmanová J, Buršíková V, Ráheľ J, Sťahel P (2019) Fast surface hydrophilization via atmospheric pressure plasma polymerization for biological and technical applications. Polymers (Basel) 11:1613. https://doi.org/10.3390/polym11101613
EN 314-1 (2005) Plywood—bond quality—part 1: test methods, Brussels, Belgium
EN 13354 (2009) Solid wood panels (SWP)—bonding quality—test method, Brussels, Belgium
EN 13353 (2011) EN 13353+A1—solid wood panels (SWP)—requirements, Brussels, Belgium
Gardner DJ, Davalos JF, Munipalle UM (1994) Adhesive bonding of pultruded fiber-reinforced plastic to wood. For Prod J 44:62–66
Greco A, Maffezzoli A, Buccoliero G, Caretto F, Cornacchia G (2013) Thermal and chemical treatments of recycled carbon fibres for improved adhesion to polymeric matrix. J Compos Mater 47:369–377. https://doi.org/10.1177/0021998312440133
Greco A, Maffezzoli A, Casciaro G, Caretto F (2014) Mechanical properties of basalt fibers and their adhesion to polypropylene matrices. Compos Part B Eng 67:233–238. https://doi.org/10.1016/j.compositesb.2014.07.020
Gur’ev VV, Neproshin EI, Mostovoi GE (2001) The effect of basalt fiber production technology on mechanical properties of fiber. Glass Ceram 58:62–65. https://doi.org/10.1023/A:1010901615857
Khelifa M, Auchet S, Méausoone P-J, Celzard A (2015) Finite element analysis of flexural strengthening of timber beams with carbon fibre-reinforced polymers. Eng Struct 101:364–375. https://doi.org/10.1016/j.engstruct.2015.07.046
Kim MT, Kim MH, Rhee KY, Park SJ (2011) Study on an oxygen plasma treatment of a basalt fiber and its effect on the interlaminar fracture property of basalt/epoxy woven composites. Compos Part B Eng 42:499–504. https://doi.org/10.1016/j.compositesb.2010.12.001
Klemberg-Sapieha JE, Küttel OM, Martinu L, Wertheimer MR (1991) Dual-frequency N 2 and NH 3 plasma modification of polyethylene and polyimide. J Vac Sci Technol A Vacuum Surf Film 9:2975–2981. https://doi.org/10.1116/1.577158
Kollmann F (1951) Technology of wood and wood based products (in German: Technologie des Holzes und der Holzwerkstoffe), 1st edn. Springer, Berlin
Konnerth J, Jäger A, Eberhardsteiner J, Müller U, Gindl W (2006) Elastic properties of adhesive polymers. II. Polymer films and bond lines by means of nanoindentation. J Appl Polym Sci 102:1234–1239. https://doi.org/10.1002/app.24427
Kramár S, Trcala M, Chitbanyong K, Král P, Puangsin B (2019) Basalt-fiber-reinforced polyvinyl acetate resin: a coating for ductile plywood panels. Materials (Basel) 13:49. https://doi.org/10.3390/ma13010049
Kramár S, Mayer AK, Schöpper C, Mai C (2020) Use of basalt scrim to enhance mechanical properties of particleboards. Constr Build Mater 238:117769. https://doi.org/10.1016/j.conbuildmat.2019.117769
Kurniawan D, Kim BS, Lee HY, Lim JY (2012) Atmospheric pressure glow discharge plasma polymerization for surface treatment on sized basalt fiber/polylactic acid composites. Compos Part B Eng 43:1010–1014. https://doi.org/10.1016/j.compositesb.2011.11.007
Ling Z, Yang H, Liu W, Zhu S, Chen X (2018) Local bond stress-slip relationships between glue laminated timber and epoxy bonded-in GFRP rod. Constr Build Mater 170:1–12. https://doi.org/10.1016/j.conbuildmat.2018.03.052
Manikandan V, Winowlin Jappes JT, Suresh Kumar SM, Amuthakkannan P (2012) Investigation of the effect of surface modifications on the mechanical properties of basalt fibre reinforced polymer composites. Compos Part B Eng 43:812–818. https://doi.org/10.1016/j.compositesb.2011.11.009
Mirzaei G, Mohebby B, Tasooji M (2012) The effect of hydrothermal treatment on bond shear strength of beech wood. Eur J Wood Prod 70:705–709. https://doi.org/10.1007/s00107-012-0608-9
Morova N (2013) Investigation of usability of basalt fibers in hot mix asphalt concrete. Constr Build Mater 47:175–180. https://doi.org/10.1016/j.conbuildmat.2013.04.048
Müller U, Sretenovic A, Vincenti A, Gindl W (2005) Direct measurement of strain distribution along a wood bond line. Part 1: shear strain concentration in a lap joint specimen by means of electronic speckle pattern interferometry. Holzforschung 59:300–306. https://doi.org/10.1515/HF.2005.050
Mutel B, Grimblot J, Dessaux O, Goudmand P (2000) XPS investigations of nitrogen-plasma-treated polypropylene in a reactor coupled to the spectrometer. Surf Interface Anal 30:401–406. https://doi.org/10.1002/1096-9918(200008)30:1%3c401::AID-SIA826%3e3.0.CO;2-G
O’Ceallaigh C, Sikora K, McPolin D, Harte AM (2018) An investigation of the viscoelastic creep behaviour of basalt fibre reinforced timber elements. Constr Build Mater 187:220–230. https://doi.org/10.1016/j.conbuildmat.2018.07.193
Onat SM, Kloeser L, Mai C (2014) An amino-alkyl siloxane oligomer as hydrophobation agent for particleboards used under high humidity conditions. Eur J Wood Prod 72:643–649. https://doi.org/10.1007/s00107-014-0829-1
Park JM, Subramanian RV (1991) Interfacial shear strength and durability improvement by monomeric and polymeric silanes in basalt fiber/epoxy single-filament composite specimens. J Adhes Sci Technol 5:459–477. https://doi.org/10.1163/156856191X00602
Park JM, Subramanian RV, Bayoumi AE (1994) Interfacial shear strength and durability improvement by silanes in single-filament composite specimens of basalt fiber in brittle phenolic and isocyanate resins. J Adhes Sci Technol 8:133–150. https://doi.org/10.1163/156856194X00113
Parker FS (1971) Amides and amines. Applications of infrared spectroscopy in biochemistry, biology, and medicine. Springer US, Boston, pp 165–172
Požgaj A, Chovanec D, Kurjatko S, Babiak M (1997) Structure and properties od wood (in Slovak: Štruktúra a vlastnosti dreva), 2nd edn. Príroda, Bratislava
Pucci MF, Liotier P-J, Drapier S (2015) Capillary effects on flax fibers—modification and characterization of the wetting dynamics. Compos Part A Appl Sci Manuf 77:257–265. https://doi.org/10.1016/j.compositesa.2015.03.010
Pucci MF, Seghini MC, Liotier P-J et al (2017) Surface characterisation and wetting properties of single basalt fibres. Compos Part B Eng 109:72–81. https://doi.org/10.1016/j.compositesb.2016.09.065
Raftery GM, Whelan C (2014) Low-grade glued laminated timber beams reinforced using improved arrangements of bonded-in GFRP rods. Constr Build Mater 52:209–220. https://doi.org/10.1016/j.conbuildmat.2013.11.044
Raftery GM, Harte AM, Rodd PD (2009) Bond quality at the FRP–wood interface using wood-laminating adhesives. Int J Adhes Adhes 29:101–110. https://doi.org/10.1016/j.ijadhadh.2008.01.006
Ráhel J, Tiňo R (2016) Wood surfaces: plasma activation. Encyclopedia of plasma technology. CRC Press, Boca Raton, pp 1541–1551
Richter K, Steiger R (2005) Thermal stability of wood-wood and wood-FRP bonding with polyurethane and epoxy adhesives. Adv Eng Mater 7:419–426. https://doi.org/10.1002/adem.200500062
Rowell RM (2012) Handbook of wood chemistry and wood composites. CRC Press, Boca Raton
Serrano E (2004) A numerical study of the shear-strength-predicting capabilities of test specimens for wood–adhesive bonds. Int J Adhes Adhes 24:23–35. https://doi.org/10.1016/S0143-7496(03)00096-4
Sikora KS, McPolin DO, Harte AM (2016) Shear strength and durability testing of adhesive bonds in cross-laminated timber. J Adhes 92:758–777. https://doi.org/10.1080/00218464.2015.1094391
Thomason J, Adzima L (2001) Sizing up the interphase: an insider’s guide to the science of sizing. Compos Part A Appl Sci Manuf 32:313–321. https://doi.org/10.1016/S1359-835X(00)00124-X
Tseng DY, Edelman ER (1998) Effects of amide and amine plasma-treated ePTFE vascular grafts on endothelial cell lining in an artificial circulatory system. J Biomed Mater Res 42:188–198. https://doi.org/10.1002/(SICI)1097-4636(199811)42:2%3c188::AID-JBM4%3e3.0.CO;2-L
Ugolev BN (2007) Wood science and forest commodity science (in Russian: Drevesinovedenie i lesnoe tovarovedenie). MGUL, Moscow
Varelidis PC, McCullough RL, Papaspyrides CD (1999) The effect on the mechanical properties of carbon/epoxy composites of polyamide coatings on the fibers. Compos Sci Technol 59:1813–1823. https://doi.org/10.1016/S0266-3538(99)00039-1
Wang GJ, Liu YW, Guo YJ, Zhang ZX, Xu MX, Yang ZX (2007) Surface modification and characterizations of basalt fibers with non-thermal plasma. Surf Coat Technol 201:6565–6568. https://doi.org/10.1016/j.surfcoat.2006.09.069
Wang J, Zhou S, Huang J, Zhao G, Liu Y (2018) Interfacial modification of basalt fiber filling composites with graphene oxide and polydopamine for enhanced mechanical and tribological properties. RSC Adv 8:12222–12231. https://doi.org/10.1039/C8RA00106E
Wei B, Cao H, Song S (2011a) Surface modification and characterization of basalt fibers with hybrid sizings. Compos Part A Appl Sci Manuf 42:22–29. https://doi.org/10.1016/j.compositesa.2010.09.010
Wei B, Song S, Cao H (2011b) Strengthening of basalt fibers with nano-SiO2-epoxy composite coating. Mater Des 32:4180–4186. https://doi.org/10.1016/j.matdes.2011.04.041
Wolkenhauer A, Militz H, Viöl W (2008) Increased PVA-glue adhesion on particle board and fibre board by plasma treatment. Holz Roh Werkst 66:143–145. https://doi.org/10.1007/s00107-007-0217-1
Živković I, Fragassa C, Pavlović A, Brugo T (2017) Influence of moisture absorption on the impact properties of flax, basalt and hybrid flax/basalt fiber reinforced green composites. Compos Part B Eng 111:148–164. https://doi.org/10.1016/j.compositesb.2016.12.018
Acknowledgements
The work at MU was supported by project CZ.1.05/2.1.00/03.0086 funded by the European Regional Development Fund and project LO1411 (NPU I) funded by the Ministry of Education, Youth, and Sports of the Czech Republic. The work at MENDELU was supported by project TJ02000171 funded by the Technology Agency of the Czech Republic.
Author information
Authors and Affiliations
Corresponding author
Ethics declarations
Conflict of interest
On behalf of all authors, the corresponding author states that there is no conflict of interest.
Additional information
Publisher's Note
Springer Nature remains neutral with regard to jurisdictional claims in published maps and institutional affiliations.
Rights and permissions
About this article
Cite this article
Kramár, S., Pipíška, T., Sťahel, P. et al. Effect of plasma sizing on basalt fibers adhesion with wood-working resins. Eur. J. Wood Prod. 79, 873–885 (2021). https://doi.org/10.1007/s00107-021-01673-7
Received:
Accepted:
Published:
Issue Date:
DOI: https://doi.org/10.1007/s00107-021-01673-7