Abstract
Diamond wire cutting is the most common method used for rock block production in quarry mining. This paper aimed to investigate the effect of operational conditions on the cutting performance of diamond wire. These operational conditions included pullback amperage, diamond bead density, the distance between cutting machine and working face, and also the number of required cutting surfaces. The effect of these factors was studied in different rock block sizes at a travertine mine in Iran; then the optimum cutting rates of the wire machine were examined in each condition. The results of this study showed that there was a significant direct relationship between the pullback amperage and the cutting rate of large surfaces. However, the relationship between the pullback amperage and the cutting rate of small surfaces was strongly indirect. Fair-large blocks with the cutting surface of 50 to 70 m2 had the highest cutting rate and the lowest specific bead consumption, as compared to the other block sizes. The optimum number of diamond beads in the unit length of the wire, for all cutting surfaces, was recommended to be 31. Also, the optimum distance between the cutting machine and the working faces for small, medium and large sizes of cutting surfaces was proposed to be 3, 3.5, and 4 m, respectively.
Similar content being viewed by others
References
Ataei M, Mikaiel R, Sereshki F, Ghaysari N (2012) Predicting the production rate of diamond wire saw using statistical analysis. Arab J Geosci 5(6):1289–1295
Aydin G, Karakurt I, Hamzacebi C (2015) Performance prediction of diamond sawblades using artificial neural network and regression analysis. Arab J Sci Eng 40(7):2003–2012
Bagherpour R, Khademian A, Almasi SN, Aalaei M (2014) Optimum cutting wire assembly in dimension stone quarries. Journal of Mining and Metallurgy a: Mining 50(1):1–8
Buyuksagis IS (2007) Effect of cutting mode on the sawability of granites using segmented circular diamond sawblade. J Mater Process Technol 183(2):399–406
Ghaysari N, Ataei M, Sereshki F, Mikaiel R (2012) Prediction of performance of diamond wire saw with respect to texture characteristics of rock/Prognozowanie Wydajności Pracy Strunowej Piły Diamentowej W Odniesieniu do Charakterystyki Tekstury Skał. Arch min Sci 57(4):887–900
Jain, S.C., Rathore, S.S., Jain, H.K., 2013. Investigation The Effects Of Machine Parameters On Cutting Performance Of Diamond Wire Saw Machine In Cutting Of Marble Bench. In International Journal of Engineering Research and Technology (Vol. 2, No. 4 (April-2013)). ESRSA Publications
Kim D, Kim H, Lee S, Lee T, Jeong H (2016) Characterization of diamond wire-cutting performance for lifetime estimation and process optimization. J Mech Sci Technol 30(2):847–852
Mikaeil R, Yousefi R, Ataei M, Farani RA (2011) Development of a new classification system for assessing of carbonate rock sawability. Arch min Sci 56(1):59–70
Ozcelik, Y., 1999. Investigation of the working conditions of diamond wire cutting machines in marble industry (Doctoral dissertation, PhD Thesis, Hacettepe University, Ankara (in Turkish)).
Özçelik, Y., Kulaksız, S., 2000. Investigation of the relationship between cutting angles and wear on beads in diamond wire cutting method. In G.N. Panagiotou and T.N. Michalakopoulos eds., Mine Planning and Equipment Selection Symposium, Athens, Greece (pp. 6–9).
Sadegheslam G, Mikaeil R, Rooki R, Ghadernejad S, Ataei M (2013) Predicting the production rate of diamond wire saws using multiple nonlinear regression analysis. Geosyst Eng 16(4):275–285
Samani HY, Bafghi ARY (2012) Prediction of the sawing quality of Marmarit stones using the capability of artificial neural network. Int J Numer Anal Methods Geomech 36(7):881–891
Sengun N, Altindag R (2013) Prediction of specific energy of carbonate rock in industrial stones cutting process. Arab J Geosci 6(4):1183–1190
Statistical Center of Iran 2016. Report Number 5, Survey Results of Iran’s Active Mines in 2014. https://www.amar.org.ir/english.
Acknowledgments
The authors would like to thank Ahrar-e-Sepahan Company, especially Eng. Majid Alaei, the head of its exploration department.
Author information
Authors and Affiliations
Corresponding author
Rights and permissions
About this article
Cite this article
Rahimdel, M.J., Bagherpour, R. Optimization of diamond wire cutting performance in travertine quarrying. Bull Eng Geol Environ 77, 1793–1801 (2018). https://doi.org/10.1007/s10064-017-1084-6
Received:
Accepted:
Published:
Issue Date:
DOI: https://doi.org/10.1007/s10064-017-1084-6