Abstract
Sulfuric acid corrosion on concrete structures is more prevalent and its damage evaluation becomes gradually imperative. This study attempts to characterize the sulfuric acid corroded surfaces of concrete in terms of three-dimensional fractal dimension. Accelerated sulfuric acid corrosion tests were conducted using concrete cylinders with six different corrosion durations, and the 3D coordinates of points on the surface of cylinders were captured using 3D laser scanning technique. The fractal dimensions were calculated using the cubic covering method, and the corrosion depth and mass loss of concrete were obtained correspondingly. The results indicated that fractal dimension can be considered as an indicator to evaluate the corrosion deterioration. The surface fractal dimension was positively correlated with the corrosion duration by a power function, where the value increased dramatically in the early stage, and gradually slowed down to maintain constant. Therefore, empirical functions to evaluate the corrosion depth and mass loss of concrete after sulfuric acid attacks were proposed. The parameters to establish the equivalent accelerated relation between experimental and natural conditions were also recommended under different degradation degrees.
Similar content being viewed by others
References
Huber, B., Hilbig, H., Drewes, J.E., Müller, E.: Evaluation of concrete corrosion after short- and long-term exposure to chemically and microbially generated sulfuric acid. Cem. Concr. Res. 94, 36–48 (2017). https://doi.org/10.1016/j.cemconres.2017.01.005
Allahverdi, A., Skvara, F.: Sulfuric acid attack on hardened paste of geopolymer cements—Part 1. Mechanism of corrosion at relatively high concentrations. Ceram. Silik. 49(4), 225 (2005). https://www.irsm.cas.cz/materialy/cs_content/2005/Allahverdi_CS_2005_0000.pdf
Xiao, J., Qu, W., Li, W., Zhu, P.: Investigation on effect of aggregate on three non-destructive testing properties of concrete subjected to sulfuric acid attack. Constr. Build. Mater. 115, 486–495 (2016). https://doi.org/10.1016/j.conbuildmat.2016.04.017
Mahdikhani, M., Bamshad, O., Shirvani, M.F.: Mechanical properties and durability of concrete specimens containing nano silica in sulfuric acid rain condition. Constr. Build. Mater. 167, 929–935 (2018). https://doi.org/10.1016/j.conbuildmat.2018.01.137
Fan, Y., Hu, Z., Zhang, Y., Liu, J.: Deterioration of compressive property of concrete under simulated acid rain environment. Constr. Build. Mater. 24(10), 1975–1983 (2010). https://doi.org/10.1016/j.conbuildmat.2010.04.002
Bassuoni, M.T., Nehdi, M.L.: Resistance of self-consolidating concrete to sulfuric acid attack with consecutive pH reduction. Cem. Concr. Res. 37(7), 1070–1084 (2007). https://doi.org/10.1016/j.cemconres.2007.04.014
Gutierrez-Padilla, M.G.D., Bielefeldt, A., Ovtchinnikov, S., Hernandez, M., Silverstein, J.: Biogenic sulfuric acid attack on different types of commercially produced concrete sewer pipes. Cem. Concr. Res. 40(2), 293–301 (2010). https://doi.org/10.1016/j.cemconres.2009.10.002
Li, X., Lin, X., Lin, K., Ji, T.: Study on the degradation mechanism of sulphoaluminate cement sea sand concrete eroded by biological sulfuric acid. Constr. Build. Mater. 157, 331–336 (2017). https://doi.org/10.1016/j.conbuildmat.2017.08.172
Girardi, F., Di Maggio, R.: Resistance of concrete mixtures to cyclic sulfuric acid exposure and mixed sulfates: effect of the type of aggregate. Cem. Concr. Compos. 33(2), 276–285 (2011). https://doi.org/10.1016/j.cemconcomp.2010.10.015
De Belie, N., Monteny, J., Beeldens, A., Vincke, E., Van Gemert, D., Verstraete, W.: Experimental research and prediction of the effect of chemical and biogenic sulfuric acid on different types of commercially produced concrete sewer pipes. Cem. Concr. Res. 34(12), 2223–2236 (2004). https://doi.org/10.1016/j.cemconres.2004.02.015
Hasan, M.S., Setunge, S., Law, D.W., Molyneaux, T.C.K.: Predicting life expectancy of concrete septic tanks exposed to sulfuric acid attack. Mag. Concr. Res. 65(13), 793–801 (2013). https://doi.org/10.1680/macr.12.00231
Pavlik, V.: Corrosion of hardened cement paste by acetic and nitric acids part I: Calculation of corrosion depth. Cem. Concr. Res. 24(3), 551–562 (1994). https://doi.org/10.1016/0008-8846(94)90144-9
Bertron, A., Duchesne, J., Escadeillas, G.: Accelerated tests of hardened cement pastes alteration by organic acids: analysis of the pH effect. Cem. Concr. Res. 35(1), 155–166 (2005). https://doi.org/10.1016/j.cemconres.2004.09.009
Monteny, J., De Belie, N., Vincke, E., Verstraete, W., Taerwe, L.: Chemical and microbiological tests to simulate sulfuric acid corrosion of polymer-modified concrete. Cem. Concr. Res. 31(9), 1359–1365 (2001). https://doi.org/10.1016/S0008-8846(01)00565-8
Mahmoodian, M., Alani, A.M.: Effect of Temperature and Acidity of Sulfuric Acid on Concrete Properties. J. Mater. Civ. Eng. 29(10), 04017154 (2017). https://doi.org/10.1061/(ASCE)MT.1943-5533.0002002
Hewayde, E., Nehdi, M.L., Allouche, E., Nakhla, G.: Using concrete admixtures for sulphuric acid resistance. Proc. ICE-Constr. Mater. 160(1), 25–35 (2007). https://doi.org/10.1680/coma.2007.160.1.25
Chang, Z.T., Song, X.J., Munn, R., Marosszeky, M.: Using limestone aggregates and different cements for enhancing resistance of concrete to sulphuric acid attack. Cem. Concr. Res. 35(8), 1486–1494 (2005). https://doi.org/10.1016/j.cemconres.2005.03.006
Nnadi, E.O., Lizarazo-Marriaga, J.: Acid corrosion of plain and reinforced concrete sewage systems. J. Mater. Civ. Eng. 25(9), 1353–1356 (2013). https://doi.org/10.1061/(asce)mt.1943-5533.0000641
Shen, Y., Wang, Y., Yang, Y., Sun, Q., Luo, T., Zhang, H.: Influence of surface roughness and hydrophilicity on bonding strength of concrete-rock interface. Constr. Build. Mater. 213, 156–166 (2019). https://doi.org/10.1016/j.conbuildmat.2019.04.078
Mohamad, M., Ibrahim, I., Abdullah, R., Rahman, A.A., Kueh, A., Usman, J.: Friction and cohesion coefficients of composite concrete-to-concrete bond. Cem. Concr. Compos. 56, 1–14 (2015). https://doi.org/10.1016/j.cemconcomp.2014.10.003
Issa, M.A., Issa, M.A., Islam, M.S., Chudnovsky, A.: Fractal dimension––a measure of fracture roughness and toughness of concrete. Eng. Fract. Mech. 70(1), 125–137 (2003). https://doi.org/10.1016/S0013-7944(02)00019-X
De Belie, N., Verschoore, R., Van Nieuwenburg, D.: Resistance of concrete with limestone sand or polymer additions to feed acids. Trans. ASAE 41(1), 227–233 (1998). https://doi.org/10.13031/2013.17155
Santos, P., Júlio, E.N.B.S.: A state-of-art review on roughness quantification methods for concrete surfaces. Constr. Build. Mater. 38(1), 912–923 (2013). https://doi.org/10.1016/j.conbuildmat.2012.09.045
De Belie, N., Monteny, J., Taerwe, L.: Apparatus for accelerated degradation testing of concrete specimens. Mater. Struct. 35(251), 427–433 (2002). https://doi.org/10.1007/BF02483147
Gruyaert, E., Van den Heede, P., Maes, M., De Belie, N.: Investigation of the influence of blast-furnace slag on the resistance of concrete against organic acid or sulphate attack by means of accelerated degradation tests. Cem. Concr. Res. 42(1), 173–185 (2012). https://doi.org/10.1016/j.cemconres.2011.09.009
Majumdar, A., Tien, C.: Fractal characterization and simulation of rough surfaces. Wear 136(2), 313–327 (1990). https://doi.org/10.1016/0043-1648(90)90154-3
Zhang, C., Chen, Y., Yao, W.: The use of fractal dimensions in the prediction of residual fatigue life of pre-corroded aluminum alloy specimens. Int. J. Fatigue. 59, 282–291 (2014). https://doi.org/10.1016/j.ijfatigue.2013.08.008
Mandelbrot, B.: How long is the coast of Britain? Statistical self-similarity and fractional dimension. Sci. 156(3775), 636–638 (1967). https://doi.org/10.1126/science.156.3775.636
Zhou, H., Xie, H.: Direct estimation of the fractal dimensions of a fracture surface of rock. Surf. Rev. Lett. 10(05), 751–762 (2003). https://doi.org/10.1142/S0218625X03005591
Lin, N., Guo, J., Xie, F., Zou, J., Tian, W., Yao, X., Zhang, H., Tang, B.: Comparison of surface fractal dimensions of chromizing coating and P110 steel for corrosion resistance estimation. Appl. Surf. Sci. 311, 330–338 (2014). https://doi.org/10.1016/j.apsusc.2014.05.062
Liang, C., Zhang, W.: Fractal characteristic of pits distribution on 304 stainless steel corroded surface and its application in corrosion diagnosis. J. Wuhan Univ. Technol. Mater. Sci. Ed. 22(3), 389–393 (2007). https://doi.org/10.1007/s11595-006-3389-3
Xu, Y.D., Qian, C.X.: Fractal characterization of corroded surface profile in reinforcing steel bars. Adv. Mater. Res. 163–167, 3118–3121 (2011). https://doi.org/10.4028/www.scientific.net/AMR.163-167.3118
Chen, X., Zhou, J., Ding, N.: Fractal characterization of pore system evolution in cementitious materials. KSCE J. Mater. Civ. Eng. 19(3), 719–724 (2015). https://doi.org/10.1007/s12205-013-0320-2
Xie, H., Wang, J., Xie, W.: Fractal effects of surface roughness on the mechanical behavior of rock joints. Chaos Soliton Fract. 8(2), 221–252 (1997). https://www.paper.edu.cn/scholar/showpdf/OUD2gN2IMTz0UxeQh
Yang, X., Zhang, R., Ma, S., Yang, X., Wang, F.: Fractal dimension of concrete meso-structure based on X-ray computed tomography. Powder Technol. 350, 91–99 (2019). https://doi.org/10.1016/j.powtec.2019.03.003
Liu, T., Zhang, X., Li, Z., Chen, Z.: Research on the homogeneity of asphalt pavement quality using X-ray computed tomography (CT) and fractal theory. Constr. Build. Mater. 68, 587–598 (2014). https://doi.org/10.1016/j.conbuildmat.2014.06.046
Liu, W., Li, Y., Chen, Q., He, X.: Accelerated corrosion environmental spectrums for testing surface coatings of critical areas of flight aircraft structures. J. Beijing Univ. Aeronaut. Astronaut. 28(1), 109–112 (2002). https://doi.org/10.13700/j.bh.1001-5965.2002.01.028
Li, X., Wang, X., Ren, H., Chen, Y., Mu, Z.: Effect of prior corrosion state on the fatigue small cracking behaviour of 6151–T6 aluminum alloy. Corros. Sci. 55, 26–33 (2012). https://doi.org/10.1016/j.corsci.2011.09.025
Jiang, X., Yang, X.: Review on the research methods of equivalent accelerated relationship in accelerated corrosion. Equip. Environ. Eng. 11(6), 50–58 (2014). https://en.cnki.com.cn/Article_en/CJFDTOTAL-JSCX201406012.htm
ACI Committee 318. Building Code Requirements for Structural Concrete (ACI 318-11) and Commentary (2011)
Zhang, W., Zhou, B., Gu, X., Dai, H.: Probability distribution model for cross-sectional area of corroded reinforcing steel bars. J. Mater. Civ. Eng. 26(5), 822–832 (2013). https://doi.org/10.1061/(ASCE)MT.1943-5533.0000888
Kim, M.K., Sohn, H., Chang, C.C.: Active dimensional quality assessment of precast concrete using 3D laser scanning. Comput. Civ. Eng. 44, 622–628 (2014). https://doi.org/10.1061/9780784413029.078
Matlab, R. Version 8.1. 0.604 (R2013a). Natrick, Massachusetts: The MathWorks Inc. (2013)
Panchenko, Y.M., Marshakov, A., Igonin, T., Kovtanyuk, V., Nikolaeva, L.: Long-term forecast of corrosion mass losses of technically important metals in various world regions using a power function. Corros. Sci. 88, 306–316 (2014). https://doi.org/10.1016/j.corsci.2014.07.049
Monteny, J., Vincke, E., Beeldens, A., De Belie, N., Taerwe, L., Van Gemert, D., Verstraete, W.: Chemical, microbiological, and in situ test methods for biogenic sulfuric acid corrosion of concrete. Cem. Concr. Res. 30(4), 623–634 (2000). https://doi.org/10.1016/S0008-8846(00)00219-2
Ji, Y., Yuan, Y., Shen, J., Ma, Y., Lai, S.: Comparison of concrete carbonation process under natural condition and high CO2 concentration environments. J. Wuhan Univ. Technol. Mater. Sci. 25(3), 515–522 (2010). https://doi.org/10.1007/s11595-030-0034-y
Neves, R., Branco, F., De Brito, J.: Field assessment of the relationship between natural and accelerated concrete carbonation resistance. Cem. Concr. Compos. 41, 9–15 (2013). https://doi.org/10.1007/s11595-030-0034-y
Gutberlet, T., Hilbig, H., Beddoe, R.: Acid attack on hydrated cement—effect of mineral acids on the degradation process. Cem. Concr. Res. 74, 35–43 (2015). https://doi.org/10.1016/j.cemconres.2015.03.011
Lloyd, R.R., Provis, J.L., van Deventer, J.S.J.: Acid resistance of inorganic polymer binders. 1. Corrosion rate. Mater. Struct. 45(1–2), 1–14 (2012). https://doi.org/10.1617/s11527-011-9744-7
Feng, L., Wang, J.: Fractal simulation of gear tooth surface. J. Mech. Transm. 38(2), 49–53 (2014). https://doi.org/10.16578/j.issn.1004.2539.2014.02.014
Ma, X., Qiu, X.: Experimental research on corrosion rules of concrete and reinforced concrete buried in acid soil. China Concr. Cem. Prod. 2, 9–13 (2000). https://doi.org/10.3969/j.issn.1000-4637.2000.02.003
Ma, X., Leng, F., Qiu, X.: Experimental studies on concrete materials in corrosive soil environment. Proc. Concr. Struct. Durability Des. Constr. 143–157 (2004). https://cpfd.cnki.com.cn/Article/CPFDTOTAL-OGTY200400006007.htm
Acknowledgements
The authors are appreciated for the financial support provided by the National Natural Science Foundation of China with Grant No. 51678430, the National Natural Science Foundation of China with No. 51808133.
Author information
Authors and Affiliations
Corresponding author
Additional information
Publisher's Note
Springer Nature remains neutral with regard to jurisdictional claims in published maps and institutional affiliations.
Rights and permissions
About this article
Cite this article
Xiao, J., Qu, W., Jiang, H. et al. Three-Dimensional Fractal Characterization of Concrete Surface Subjected to Sulfuric Acid Attacks. J Nondestruct Eval 39, 57 (2020). https://doi.org/10.1007/s10921-020-00689-y
Received:
Accepted:
Published:
DOI: https://doi.org/10.1007/s10921-020-00689-y