Abstract
The effects of a new mechanical surface treatment method, called ultrasonic nanocrystal surface modification (UNSM), on near-surface microstructures and residual stress states as well as on the fatigue behavior of an austenitic steel AISI 304 are investigated and discussed. The results are compared with consequences of other mechanical surface treatment methods such as deep rolling or shot peening.
Similar content being viewed by others
References
A. Niku-Lari (Ed), Advances in Surface Treatments, Pergamon Press, Oxford (1987)
B. Scholtes, Assessment of Residual Stresses, Structural and Residual Stress Analyses by Nondestructive Methods, V. Hauk, Ed., Elsevier, Amsterdam, 1997, p 590–632
L. Wagner, Mechanical Surface Treatments on Titanium, Aluminum and Magnesium Alloys, Mater. Sci. Eng. A 263, 210–216 (1999)
B. Scholtes and E. Macherauch, Auswirkung mechanischer Randschichtverformungen auf das Festigkeitsverhalten metallischer Werkstoffe, Z. Metallkd., 1986, 77(5), S. 322
V. Schultze, Modern Mechanical Surface Treatment, Wiley-VCH, Weinheim (2005)
R. K. Nalla, I. Altenberger, I. Noster, G. Y. Lui, B. Scholtes, R. O. Ritchie, On the Influence of Mechanical Surface Treatments—Deep Rolling and Laser Shock Peening—on the Fatigue Behaviour of Ti-6Al-4V at Ambient and Elevated Temperatures, Mater. Sci. Eng. A 355, 216–230 (2003)
I. Altenberger, B. Scholtes, U. Martin, H. Oettel, Cycle Deformation and Near Surface Microstructures of Shot Peened or Deep Rolled Austenitic Steel AISI 304, Mater. Sci. Eng. A 264, 1–16 (1999)
Y.-S. Pyun, H.S. Kim, K.G. Son, G.H. Song, M.K. Kim, J.H. Kang B.U. Choi, J. Park, I.H. Cho, C.S. Kim, J.H. Park, and J. Kinney, Development of D2 Tool Steel Trimming Knives with Nanoscale Microstructure, Proceedings of the AISTech Conference, Vol. 2, 2005, p 465–474
C.-M. Suh, G.-H. Song, M.-S. Suh, Y.-S. Pyoun, Fatigue and Mechanical Characteristics of Nano-Structured Tool Steel by Ultrasonic Cold Forging Technology, Mater. Sci. Eng. A 443, 101–106 (2007)
B. Scholtes and E. Macherauch (1987) Eigenspannungsanalysen unter partieller Probenzerstörung mit Hilfe von Röntgenographischer Methoden. Deutscher Verband für Materialprüfung E.V., Berlin, p 301–312
I. Nikitin, I. Altenberger, Comparison of the Fatigue Behavior and Residual Stress Stability of Laser-Shock Peened and Deep Rolled Austenitic Stainless Steel AISI 304 in the Temperature Range 25–600 °C, Mater. Sci. Eng. A 465, 176–182 (2007)
I. Altenberger, Mikrostrukturelle Untersuchungen mechanisch randschichtverfestigter Bereiche schwingend beanspruchter metallischer Werkstoffe, Forschungsberichte aus dem Institut für Werkstofftechnik, Metallische Werkstoffe, 1999
Author information
Authors and Affiliations
Corresponding author
Rights and permissions
About this article
Cite this article
Cherif, A., Pyoun, Y. & Scholtes, B. Effects of Ultrasonic Nanocrystal Surface Modification (UNSM) on Residual Stress State and Fatigue Strength of AISI 304. J. of Materi Eng and Perform 19, 282–286 (2010). https://doi.org/10.1007/s11665-009-9445-3
Received:
Revised:
Accepted:
Published:
Issue Date:
DOI: https://doi.org/10.1007/s11665-009-9445-3