Abstract
In order to increase the strength and deformation capacity of flat slabs, punching shear reinforcement is used as an effective solution. Several types of punching shear reinforcing systems have been developed in the past. This work aims to analyze the behavior of unbonded post-tensioned slab subjected to punching load provided with “Inverted-U Shaped Reinforcement”. By using a finite element software, the results were compared with that obtained from an experimental investigation previously done. The experimental results were also compared according to ACI provisions for punching shear strength. Good correlation was done between what was tested and the numerical results.
Similar content being viewed by others
References
ABAQUS 6.13 (2014). ABAQUS/CAE User’s Guide, Providence, RI.
Abou Saleh, Z. and Suaris, W. P. E. (2007). “Punching shear capacity of post-tensioned slab with hairpin shaped reinforcements.” PTI Journal. https://doi.org/www.post-tensioning.org/Uploads/Publications/PTI%20Journal/151209-Journal%20Article%20Reprint%20Request%20Form.pdf
ACI Building (2011). Code Requirements for Structural Concrete, ACI 318–11, American Concrete Institute, ACI Committee 318, p. 503, Detroit.
ACI Committee 318 (1971). Building Code Requirements for Reinforced Concrete (ACI 318-71), American Concrete Institute, Detroit, Michigan.
ACI Committee 318 (2014). Building Code Requirements for Reinforced Concrete (ACI 318-14), American Concrete Institute, Farmington Hills, MI.
Baalbaki, O. (2012). “A practical strengthening scheme of reinforced concrete beams using Post-Tensioning tendons.” European Journal of Scientific Research, Vol. 83, No. 1, ISSN 1450-216X.
Cheng, M. Y. and Parra-Montesinos, G. J. (2010). “Evaluation of steel fiber reinforcement for punching shear resistance in Slab-Column Connections-Part II: Lateral displacement reversals.” ACI Structural Journal, Vol. 107, No. 1, pp. 110–118, MS No. S-2009-039.R1.
Cicekli, U., Voyiadjis, G. Z., and Abu Al-Rub, R. K. (2007). “A plasticity and anisotropic damage model for plain concrete.” International Journal of Plasticity, Vol. 23, pp. 1874–1900, DOI: 10.1016/j.ijplas.2007.03.006.
Clement, T., Ramos, A. P., Ruiz, M. F., and Muttoni, A. (2013). “Design for punching of prestressed concrete slabs.” Structural Concrete, Vol. 14, No. 2, pp. 157–167, DOI: 10.1002/suco.201200028.
Corley, W. G. and Hawkins, N. M. (1968). “Shearhead reinforcement for slabs.” ACI Journal Proceedings, Vol. 65, No. 10, pp. 811–824.
El-Salakawy, E. F., Polak, M. A., and Soudki, K. A. (2003). “New shear strengthening technique for concrete slab-column connections.” ACI Structural Journal, Vol. 100, No. 3, pp. 297–304, ISSN: 0889–3241.
Eurocode 2 (2004). Design of concrete structures -Part 1-1: General rules and rules for buildings, European Committee for Standardization (CEN), Brussels, December.
Fernandez Ruiz, M., Mirzaei, Y., and Muttoni, A. (2013). “Post-punching behavior of flat slabs.” ACI Structural Journal, Vol. 110, No. 5, pp. 801–811, MS No. S-2011-307.
FIB Model Code 2010 (2012). Final Draft, Vol 1, p. 653, Lausanne, Suisse, ISBN 978-2-88394-105-2.
Gouveia, N. D, Lapi, M., Orlando, M., Faria, D. M. V., and Ramos, A. M. P. (2017). “Experimental and theoretical evaluation of punching strength of steel fiber reinforced concrete slabs.” Structural Concrete, pp. 1–13, DOI: 10.1002/suco.201700136.
Harajli, M. H., Maalouf, D., and Khatib, H. (1995). “Effect of fibers on the punching shear strength of slab-column connections.” Cement and Concrete Composites, Vol. 17, No. 2, pp. 161–170, DOI: 10.1016/0958-9465(94)00031-S.
Hawkins, N. M. (1974). “Shear strength of slabs with shear reinforcements.” Shear in Reinforced Concrete, American Concrete Institute, Farmington hills, MI.
Koppitz, R., Kenel, A., and Keller, T. (2013). “Punching shear of RC flat slabs -review of analytical models for new and strengthening of existing slabs.” Engineering Structures, Vol. 52, pp. 123–130, DOI: 10.1016/j.engstruct.2013.02.014.
Lapi, M., Fernandes, H., Orlando, M., Ramos, A., and Lúcio, V. (2017). “Performance assessment of flat slabs strengthened with a bonded reinforced-concrete overlay.” Magazine of Concrete Research, Vol. 70, No. 9, pp. 433–451, DOI: 10.1680/jmacr.17.00037.
Lee, J. and Fenves, G. L. (1998). “Plastic-damage model for cyclic loading of concrete structures.” Journal of Engineering Mechanics, Vol. 124, No. 8, pp. 892–900, DOI: 10.1061/(ASCE)0733-9399 (1998)124:8(892).
Moe, J. (1961). Shearing Strength of Reinforced Slabs and Footings under Concentrated Load, Bulletin D47, Portland Cement Association, p. 130.
Pilakoutas, K. and Li, X. (1961). “Alternative shear reinforcement for reinforced concrete flat slabs.” Journal of Structural Engineering, Vol. 129, No. 9, pp. 1164–1172, DOI: 10.1061/(ASCE)0733-9445 (2003)129:9(1164).
Qin, F., Yi, H., Ya-dong, Z., and Li, C. (2007). “Investigation into static properties of damaged plasticity model for concrete in ABAQUS.” Journal of PLA University of Science and Technology, Vol. 8, No. 3, pp. 254–260, https://doi.org/en.cnki.com.cn/Article_en/CJFDTOTALJFJL200703010.htm
Subedi, N. K. and Baglin, P. S. (2003). “Design of slab-column junctions in flat slabs.” Proceedings of the Institution of Civil Engineers, Structures and Buildings, Vol. 156, No. 3, pp. 319–331, DOI: 10.1680/stbu.2003.156.3.319.
Sümer, Y. and Aktas, M. (2015). “Defining parameters for concrete damage plasticity model.” Challenge Journal of Structural Mechanics, Vol. 1, No. 3, pp. 149–155, DOI: 10.20528/cjsmec.2015.07.023.
Talbot, A. N. (1913). Reinforced Concrete Wall Footings and Columns under Concentrated Loads, Research and Development, Bulletin D47, Illinois.
Tasker, H. Z. and Wyatt, R. J. (1963). Shear in Flat-Plate Construction under Uniform Loading, Special Report No. 23, Australian Commonwealth Experimental Building Station, Sydney, Australia.
Viest, I. M. (1956). Test of Stud shear connectors, Parts I, II, III and IV, Engrg. Test Data, Nelson Stud Welding, Lorain, Ohio.
Author information
Authors and Affiliations
Corresponding author
Rights and permissions
About this article
Cite this article
Khatib, M., Abou Saleh, Z., Baalbaki, O. et al. Numerical Punching Shear Analysis of Unbonded Post-Tensioned Slabs with Inverted-U Shaped. KSCE J Civ Eng 22, 4490–4499 (2018). https://doi.org/10.1007/s12205-018-1505-5
Received:
Revised:
Accepted:
Published:
Issue Date:
DOI: https://doi.org/10.1007/s12205-018-1505-5