Abstract
An extensive parametric numerical study was performed after completed experimental campaign of timber-glass hybrid walls (TGW and TGWE). 36 timber-glass models (TG) with different outer dimensions were built and analysed with a goal to capture the basic response of mechanically tested timber-glass walls and to determine the racking stiffness of the calculated numerical models. Timber frame was modelled using linear beam elements with hinges in all four corners, an IGU was modelled as a multilayer shell and finally a layer of adhesive was modelled with linear and nonlinear springs, which were distributed circumferentially around the edge of IGU and connected onto a timber frame. Normal and shear stiffness coefficients for linear-elastic springs were calculated, while for nonlinear springs a special series of mechanical tests on polyurethane (PU) adhesive was performed since a lack of data available in addition to the desired amount of information needed for the numerical analysis. Uniaxial tension, compression and shear tests were made to obtain the results in form of the load-displacement curve, which presented a direct input for nonlinear normal and shear springs of the mathematical model. For each compression and tension mechanical test three specimens were prepared and tested up to rupture, while a double-lap shear test was conducted using two specimens giving two results each. PU adhesive specimens of the first series had dimensions of 50 mm \(\times \) 50 mm and thickness of 5.0 mm. Mechanical tests were repeated for two additional thicknesses of PU adhesive, namely 7.0 mm and 9.0 mm. After completed experimental investigation on PU adhesive joint, together 108 numerical models with different external dimensions were analysed in commercial code SAP2000. Having the correct information about the stiffness of the single TG shear wall one can calculate the stiffness of the entire timber-glass building built with such walls.
Similar content being viewed by others
References
Amadio, C., Bedon, C.: Effect of circumferential sealant joints and metal supporting frames on the buckling behavior of glass panels subjected to in-plane shear loads. Glass Struct. Eng. (2016). https://doi.org/10.1007/s40940-015-0001-2
Bedon, C., Amadio, C.: A unified approach for the shear buckling design of structural glass walls with non-ideal restrains. Am. J. Eng. Appl. Sci. (2016). https://doi.org/10.3844/ajeassp.2016
Bedon, C., Amadio, C.: Buckling analysis and design proposal for 2-side supported double insulated glass units (IGUs) in compression. Eng. Struct. (2018). https://doi.org/10.1016/j.engstruct.2018.04.055
Ber, B., Premrov, M., Štrukelj, A., Kuhta, M.: Experimental investigations of timber-glass composite wall panels. Constr. Build. Mater. (2014). https://doi.org/10.1016/j.conbuildmat.2014.05.044
Ber, B., Šušteršič, I., Premrov, M., Štrukelj, A., Dujič, B.: Testing of timber-glass composite walls. Proc. Inst. Civ. Eng. Struct. Build. (2015). https://doi.org/10.1680/stbu.13.00105
Ber, B., Premrov, M., Štrukelj, A.: Finite element analysis of timber-glass walls. Glass Struct. Eng. (2016). https://doi.org/10.1007/s40940-016-0015-4
Blyberg, L., Serrano, E., Enquist, B., Sterley, M.: Adhesive joint for structural timber/glass applications: experimental testing and evaluation methods. Int. J. Adhes. Adhes. (2012). https://doi.org/10.1016/j.ijadhadh.2012.02.008
Blyberg, L., Lang, M., Lundstedt, K., Schander, M., Serrano, E., Silfverheilm, M., Stalhandske, C.: Glass, timber and adhesive joints: innovative load bearing building components. Constr. Build. Mater. (2014). https://doi.org/10.1016/j.conbuildmat.2014.01.045
Frangež, R., Ber, B., Premrov, M.: Experimental and numerical investigations of timber-glass shear walls. In: Proceedings of the World Conference on Timber Engineering, Vienna, Austria (2016)
Hochhauser, W.: A contribution to the calculation and sizing of glued and embedded timber-glass composite panes. Ph.D. Thesis. Vienna University of Technology, Austria (2011)
Huveners, E.M.P., van Herwijnen, F., Soetens, F., Hofmeyer, H.: Mechanical shear properties of adhesives. In: Proceedings of Glass Performance Days, Tampere, Finland (2007)
Huveners, E.M.P.: Circumferentially adhesive bonded glass panes for bracing steel frames in facades. Ph.D. Thesis. University of Technology Eindhoven, Netherlands (2009)
Kozłowski, M., Dorn, M., Serrano, E.: Experimental testing of load-bearing timber-glass composite shear walls and beams. Wood Mater. Sci. Eng. (2015). https://doi.org/10.1080/17480272.2015.1061595
Niklisch, F., Hernandez Maetschl, S., Schlehlein, M., Weller, B.: Development of load-bearing timber-glass composite shear wall elements. In: Proceedings of Glass Performance Days, Tampere, Finland (2015)
Premrov, M., Žegarac Leskovar, V., Mihalič, K.: Influence of the building shape on the energy performance of timber-glass buildings in different climatic conditions. Energy (2016). https://doi.org/10.1016/j.energy.2015.05.027
Premrov, M., Ber, B., Štrukelj, A.: Cyclic and shaking-table tests of timber-glass buildings. Int. J. Comput. Methods Exp. Meas. (2017). https://doi.org/10.2495/CMEM-V5-N6-928-939
Štrukelj, A., Ber, B., Premrov, M.: Racking resistance of timber-glass elements using different types of adhesives. Constr. Build. Mater. (2015). https://doi.org/10.1016/j.conbuildmat.2015.05.112
Weller, B., Aßmus, E., Niklisch, F.: Assessment of the suitability of adhesives for load-bearing timber-glass composite elements. In: Proceedings of Glass Performance Days, Tampere, Finland (2013)
Winter, W., Hochhauser, W., Kreher, K.: Load bearing and stiffening timber-glass-composites (TGC). In: Proceedings of the World Conference on Timber Engineering (2010)
Acknowledgements
The investment is co-financed by the Republic of Slovenia and the European Union under the European Regional Development Fund.
Author information
Authors and Affiliations
Corresponding author
Additional information
Publisher's Note
Springer Nature remains neutral with regard to jurisdictional claims in published maps and institutional affiliations.
Rights and permissions
About this article
Cite this article
Ber, B., Finžgar, G., Premrov, M. et al. On parameters affecting the racking stiffness of timber-glass walls. Glass Struct Eng 4, 69–82 (2019). https://doi.org/10.1007/s40940-018-0086-5
Received:
Accepted:
Published:
Issue Date:
DOI: https://doi.org/10.1007/s40940-018-0086-5