Abstract
Multichip packaging is receiving increased attention as electronic equipment manufacturers drive toward smaller, faster and less expensive products. By connecting several chips together in a single package:
-
Board size can be reduced by up to a factor of 10 or more
-
Signal propagation between chips can be up to three times faster
-
The number of solder connections in a system can be reduced
Even so, multichip modules (MCMs) will be utilized only where they are the least expensive method of meeting system requirements. The choice of MCM materials and manufacturing processes greatly influences the cost of a multichip module technology in terms of piece part cost, manufacturing yield, manufacturing cycle time and repairability. Materials choices are also dominant factors in the electrical and thermal performance of a module. There is no single “right” choice; rather, different choices are appropriate for different applications.
Access this chapter
Tax calculation will be finalised at checkout
Purchases are for personal use only
Preview
Unable to display preview. Download preview PDF.
References
J. L. Sprague, “Multilayer Ceramic Packaging Alternatives,” IEEE Trans. on Components, Hybrids, and Manuf. Tech., vol. 13, no. 2, pp. 390–369, June 1990.
U. Deshpande, S. Shamouilian, G. Howell, “High Density Interconnect Technology for VAX-9000 System,” Internat. Electr. Packaging Soc., 1EPS, (Marlborough MA), Sept. 1990.
Design Guidelines Multilayer Ceramic, Kyocera Corporation.
Design Guide: Developing Customized Microelectronic Packaging for High-Performance Applications, Dupont Electronics.
M. R. Cox, L. Ng, “An Economic Comparison of High and Low Temperature Cofired Ceramic,” Inside ISHM pp. 31–33, Jan./Feb. 1992.
S. J. Stein, R. L. Wahlers, C. Haung, M. Stein, “Interconnection and Packaging of Advanced Electronic Circuitry,” Proc. ISHM, (Orlando, FL), pp.130–134, Oct. 1991.
N. Iwase, K. Anzai, K. Shinozaki, “Aluminum Nitride Substrates Having High Thermal Conductivity,” Solid State Techn., pp. 135–138, Oct. 1986.
D. J. Arthur, “Advanced Fluoropolymer Dielectrics for MCM Packaging,” First Internat. Conf. on Multichip Modules, (Denver CO), pp. 270–276, April 1992.
P. Fischer, “Materials for a Parallel Approach to High Density Interconnects,” Proc. IEPS, (Marlborough MA), p. 103, 1990.
T. G. Tessier, W. F. Hoffman, J. W. Stafford, “Via Processing Options for MCM-D Fabrication: Excimer Laser Ablation vs. Reactive Ion Etching”, Proc. 41st Electronics Components Techn. Conf, (Atlanta GA), pp. 827–834, May 1991.
R. C. Eden, “Applicability of Diamond Substrates to Multi-Chip Modules,” Proc. ISHM, (Orlando FL), pp. 363–367, Oct. 1991.
J. W. Balde, “Proposed MCM Standard Sizes - A Report of the IEEE Task Force”, Proc. NEPCON West, (Anaheim CA), pp. 467–478, Feb. 1992.
R. A. Dovich, Reliability Statistics, Milwaukee, Wisconsin: ASQC Quality Press, pp. 21–35.
A. Krauter, J. Baumann, M. Becker, “Assembly Process for a New Packaging System,” Siemens Research and Development Reports, Bd. 17, 1988, No. 5, Springer-Verlag.
J. Hardy, High Frequency Circuit Design, Virginia: Reston Publishing Company, 1979.
H. B. Bakoglo, Circuits, Interconnects and Packaging for VLSI, New York: Addison-Wesley Publishing Company, 1990.
H. Brosamle, B. Brabetz, V. Ehrenstein, F. Bachmann, “Technology for a Microwiring Substrate,” Siemens Research and Development Reports, Bd. 17, 1988, Nr. 5 Springer-Verlag.
E. G. Myszka, A. Casey, J. Trent, “A Multichip Package for High Speed Logic Die,” Proc. 42nd Electronic Components Techn, Conf, (San Diego CA), pp. 991–996, May 1992.
J. Trent, G. Westbrook, “Fine Pitch Pad Array Carrier Sockets for High Speed Logic Die,” IEEE Multichip Module Conf,(Santa Cruz CA), pp. 40–43, March 1992.
B. K. Gilbert, W. L. Walters, “Design Options for Digital Multichip Modules Operating at High System Clock Rates,” First Internat. Conf. on Multichip Modules, (Denver CO), pp. 167–173, April 1992.
C. T. Sullivan, “Optical Waveguide Circuits for Printed Wire-Board Interconnections,” Optoelectonic Materials, Devices, Packaging and Interconnects, SPIE vol. 994, pp. 92–100, 1988.
K. W. Jelley, G. T. Valliath, J. W. Stafford, “1 Gbit/s NRZ Chip-To-Chip Optical Interconnect,” Photon. Tech. Lett., to be published.
R. Darveaux, I. Turlik, “Backside Cooling of Flip Chip Devices in Multichip Modules,” First Internat. Conf. on Multichip Modules, (Denver CO), pp. 230–241, April 1992.
F. Klimpl, “Basics of Multilayer Matter,” Electronic Engineering Times, Issue 681, Feb. 1992.
C. Melton, A. Skipor, J. Thome, “Manufacturing Process Issues of Non Lead Bearing Solder Pastes,” Internat. Conf. on Solder Fluxes and Pastes, (Atlanta GA), May 1992.
Editor information
Rights and permissions
Copyright information
© 1993 Springer Science+Business Media New York
About this chapter
Cite this chapter
Dixon, A.C., Myszka, E.G. (1993). MCM Package Selection: A Materials and Manufacturing Perspective. In: Doane, D.A., Franzon, P.D. (eds) Multichip Module Technologies and Alternatives: The Basics. Springer, Boston, MA. https://doi.org/10.1007/978-1-4615-3100-5_2
Download citation
DOI: https://doi.org/10.1007/978-1-4615-3100-5_2
Publisher Name: Springer, Boston, MA
Print ISBN: 978-0-442-01236-6
Online ISBN: 978-1-4615-3100-5
eBook Packages: Springer Book Archive