Abstract
In this chapter, the physical characteristics and the functions of the electrodes are reported. In the first part, the differences between the various types of electrodes, the biochemical mechanisms of electrical conduction and the electrode chloridation methods are described. The second part is dedicated to the description of standard EEG electrodes (intrinsic properties, positioning, caps, adhesive pastes). Finally, a description of characteristics and indications of special electrodes is also reported.
Access this chapter
Tax calculation will be finalised at checkout
Purchases are for personal use only
References
Neuman MR. Biopotential electrodes. In: Webster JG, editor. Medical instrumentation: application and design. 4th ed. Hoboken, NJ: John Wiley & Sons Inc.; 2010. p. 189–240.
Rowe BC. Bioelectricity and its measurement. In: Kutz M, editor. Standard handbook of biomedical engineering and design. New York: McGraw-Hill; 2003. p. 1–50.
Falco C, Sebastiano F, Cacciola L, et al. Scalp electrode placement by EC2 adhesive paste in long-term video-EEG monitoring. Clin Neurophysiol. 2005;116:1771–3.
Dash D, Dash C, Primrose S, et al. Update on minimal standards for electroencephalography in Canada: a review by the Canadian Society of Clinical Neurophysiologists. Can J Neurol Sci. 2017;44:631–42.
Epstein CM, et al. Guidelines Review Committee. American Clinical Neurophysiology Society. Guideline 1: minimum technical requirements for performing clinical electroencephalography. J Clin Neurophysiol. 2006;23:86–91.
Sinha SR, Sullivan S, Sabau D, et al. American Clinical Neurophysiology Society Guideline 1: minimum technical requirements for performing clinical electroencephalography. J Clin Neurophysiol. 2016;33:303–7.
Searle A, Kirkup L. A direct comparison of wet, dry and insulating bioelectric recording electrodes. Physiol Meas. 2000;21:271–83.
Metting van Rijn AC, Peper A, Grimbergen CA. High-quality recording of bioelectric events. Part 2. Low-noise, low-power multichannel amplifier design. Med Biol Eng Comput. 1991;29:433–40.
Lin CT, Liao LD, Liu YH, Wang IJ, Lin BS, Chang JY. Novel dry polymer foam electrodes for long-term EEG measurement. IEEE Trans Biomed Eng. 2011;58:1200–7.
Grozea C, Voinescu CD, Fazli S. Bristle-sensors-low-cost flexible passive dry EEG electrodes for neurofeedback and BCI applications. J Neural Eng. 2011;8:1–14.
Lee SM, Kim JH, Byeon HJ, Choi YY, Park KS, Lee SH. A capacitive biocompatible and adhesive electrode for long-term and cap-free monitoring of EEG signals. J Neural Eng. 2013;10:036006.
Chen YH, Op de Beeck M, Vanderheyden L, Mihajlovic V, Grundlehner B, Van Hoof C. Comb-shaped polymer-based dry electrodes for EEG/ECG measurements with high user comfort. Conf Proc IEEE Eng Med Biol Soc. 2013;2013:551–4.
Fiedler P, Pedrosa P, Griebel S, Fonseca C, Vaz F, Supriyanto E, Zanow F, Haueisen J. Novel multipin electrode cap system for dry electroencephalography. Brain Topogr. 2015;28:647–56.
Metting van Rijn AC, Peper A, Grimbergen CA. High-quality recording of bioelectric events. Part 1. Interference reduction, theory and practice. Med Biol Eng Comput. 1990;28:389–97.
Xu J, Mitra S, Van Hoof C, Yazicioglu RF, Makinwa KAA. Active electrodes for wearable EEG acquisition: review and electronics design methodology. IEEE Rev Biomed Eng. 2017;10:187–98.
Jones D. Recording of the basal electroencephalogram with sphenoidal electrodes. Electroencephalogr Clin Neurophysiol. 1951;3:100.
American EEG Society. Report of the committee on infectious diseases. J Clin Neurophysiol. 1994;11:128–32.
Scott NK. Infection prevention: 2013 review sand update for neurodiagnostic technologists. Neurodiagn J. 2013;53:271–88.
Author information
Authors and Affiliations
Corresponding author
Editor information
Editors and Affiliations
Appendix: Electro-Physical Characteristics of Electrodes
Appendix: Electro-Physical Characteristics of Electrodes
Silver (Ag): it is a transition, pliable, biocompatible metal for non-invasive use only. It is characterised by a higher electrical conductivity than the other metals and by a medium/low level of electrode potential. It is subjected to a fast oxidation in contact with ozone and therefore the air. It is often used as a basic material in the production of surface electrodes, and in order to reduce to the minimum the inherent noise, it is essential to use the 999% pure one. The pure silver is a non-magnetic metal.
Silver/silver chloride (Ag/AgCl): it is a mixed material with pure silver base and an external layer of silver chloride. The external match between silver metal and silver chloride salt guarantees unique features for the electrode. This mixed material is characterised by a fixed and specific electrode potential and by a low electrode/skin contact impedance. Therefore, it is perfect for recordings of low levels of AC and DC potentials and shows lower noises in low frequency in comparison with gold and pure silver. The layer of chloride silver that covers silver can be achieved through a chemical or electrolytic process. Both treatments make the electrode to get a characteristic dark grey colouring. Being of a least thickness, this external coat can deteriorate in the long term if high-saline content pastes and gel are used and if they are not removed at the end of use conveniently. Moreover, it is necessary to pay a particular attention to external mechanical abrasions that could take the treatment away. In case of a continuous employment, a treatment of re-chlorinating is needed when you notice the surface of the electrode has lost its original colour.
Sintered silver/silver chloride (Sint Ag/AgCl): it has the same electrical features of Ag/AgCl as it is formed by a mixture of Ag and AgCl very thin powders that are compacted through the sintering process. Therefore, you get an electrode of uniform thickness characterised by a greater stability of electrical features in the long term compared to an average Ag/AgCl. With regard to maintenance, this type of electrode does not need to be re-chlorinated but only to remove the remains of gel and conductive paste carefully.
Gold (Au): it is a transition, pliable, biocompatible metal used also for invasive employment. It is characterised by an excellent electrical conductivity, by a medium/low electrode potential and by the fact it is resistant to most chemical compounds. These features make it perfect for an employment with strong saline-based electrolytes and adhesives or diluents of a various nature. It is often employed as an external coat in the production of cup electrodes to be used in long terms monitoring or for sleep studies, as adhesives and diluents strong like collodion and acetone are applied with the electrode. Owing to a high biocompatibility, it is often used for invasive electrodes for recording of both potentials and electric stimulation.
Tin (Sn): it is a post-transition, pliable and resistant to metal corrosion. It is characterised by a good electrical conductivity, low level of electrode potential and a low level of innate noise. It is the material with the best value/quality relationship in the production of electrodes, and historically it is used in the production of head caps with prewired electrodes.
Carbon/graphite (C): it is a non-metal material with a good electrical conductivity; it has a very low level of electrode potential and shows a low level of noise similar to Ag/AgCL. Moreover, it has the quality to be radium-opaque and non-magnetic. Often, the graphite powder is inserted into plastics and paints to be employed in the production of electrodes. This solution makes the electrical features of this material worse but makes it easily usable in manufacturing systems.
Steel (alloys AISI 304,316): biocompatible, of high hardness and elastic alloy, characterised by a remarkable resistance to corrosion in water and in the air. It gives a medium electrical conductivity. Owing to mechanical and ductile features, it is used in the production of medical needles. Given its wide employment in the medical field, it guarantees the best quality/price relationship.
Platinum (Pt): it is a transition, pliable metal; it has a strong resistance to corrosion and is biocompatible. Usually it is used in alloy with iridium to improve its mechanical resistance. It is recognised for its good electrical conductivity and is employed for cortical electrodes and needles. It is a non-magnetic material.
Titanium (Gr. 5): it is a light and resistant metal, both mechanically and chemically. It is a biocompatible material and customarily is employed in prostheses. As far as the electrical characteristics, they are similar to tins. It is a non-magnetic material and for this feature it is used for MRI compatible products, especially needle electrodes, owing to its physical characteristics like steel. Given its high level of biocompatibility and resistance, it is also used for long-duration applied electrodes and implantable electrodes.
Rights and permissions
Copyright information
© 2019 Springer Nature Switzerland AG
About this chapter
Cite this chapter
Mecarelli, O., Panzica, F. (2019). Scalp and Special Electrodes. In: Mecarelli, O. (eds) Clinical Electroencephalography. Springer, Cham. https://doi.org/10.1007/978-3-030-04573-9_3
Download citation
DOI: https://doi.org/10.1007/978-3-030-04573-9_3
Publisher Name: Springer, Cham
Print ISBN: 978-3-030-04572-2
Online ISBN: 978-3-030-04573-9
eBook Packages: MedicineMedicine (R0)