Abstract
Recently, the Parallel Manipulators (PMs) attract the attention of the researchers. This research work is concerned with the Planar Parallel Manipulators (PPMs). An investigation led to a comparative study between the 2-RRR PPM and 3-RRR PPM. The 2-RRR non redundant PPM and 3-RRR redundant PPM, with 2-degree-of freedom, are considered. These two PPMs are introduced with their mechanism construction. The workspace, different properties and performance indices are carried out. Investigation of characteristics of these manipulators should go through the complexity of the direct and inverse kinematics problems, which are solved using the suggested and proper geometrical equations. The dexterous workspace is geometrically obtained where the End-Effector (EE) can reach and illustrate some of its properties. The Jacobian matrix for these manipulators is essential method to complete this analysis. This work is terminated by two characteristic maps of these two manipulators, which are dexterity and manipulability indices that were covering the workspace.
Access this chapter
Tax calculation will be finalised at checkout
Purchases are for personal use only
References
Patel, Y.D., George, P.M.: Parallel manipulators applicationsa survey. Mod. Mech. Eng. 2(03), 57 (2012)
Pandilov, Z., Dukovski, V.: Comparison of the characteristics between serial and parallel robots. Acta Technica Corviniensis-Bull. Eng. 7(1) (2014)
Blan, R., Mties, V., Stan, S., Lpuan, C.: On the Control of a 3-RRR Planar Parallel Minirobot. Mecatronica (4) (2004)
Tsai, L.W.: Robot Analysis: The Mechanics of Serial and Parallel Manipulators. Wiley (1999)
Dash, A.K., Chen, I.M., Yeo, S.H., Yang, G.: Task-oriented configuration design for reconfigurable parallel manipulator systems. Int. J. Comput. Integr. Manuf. 18(7), 615–634 (2005)
Maciejewski, A.A., Klein, C.A.: Obstacle avoidance for kinematically redundant manipulators in dynamically varying environments. Int. J. Robot. Res. 4(3), 109–117 (1985)
Nakamura, Y., Hanafusa, H., Yoshikawa, T.: Task-priority based redundancy control of robot manipulators. Int. J. Robot. Res. (1987)
Wang, J., Gosselin, C.M.: Kinematic analysis and design of kinematically redundant parallel mechanisms. Trans.-Am. Soc. Mech. Eng. J,. Mech. Des. 126(1) (2004)
Shang, W., Cong, S.: Dexterity and adaptive control of planar parallel manipulators with and without redundant actuation. J. Comput. Nonlinear Dyn. 10(1), 011002 (2015)
Cheng, H., Yiu, Y.K., Li, Z.: Dynamics and control of redundantly actuated parallel manipulators. IEEE/ASME Trans. Mechatron. 8(4) (2003)
Shayya, S., Krut, S., Baradat, C., Pierrot, F.: Dynamic analysis of 4 degrees of freedom redundant parallel manipulator. In: Advances in Robot Kinematics, pp. 545–553. Springer (2014)
Shang, W., Cong, S., Kong, F.: Identification of dynamic and friction parameters of a parallel manipulator with actuation redundancy. Mechatronics 20(2) (2010)
Paccot, F., Andreff, N., Martinet, P.: A review on the dynamic control of parallel kinematic machines: theory and experiments. Int. J. Robot. Res. 28(3), 395–416 (2009)
Ghorbel, F.H., Chtelat, O., Gunawardana, R., Longchamp, R.: Modeling and set point control of closed-chain mechanisms: theory and experiment. IEEE Trans. Control Syst. Technol. 8(5), 801–815 (2000)
Shang, W.W., Cong, S., Li, Z.X., Jiang, S.L.: Augmented nonlinear PD controller for a redundantly actuated parallel manipulator. Adv. Robot. (2009)
Gosselin, C., Angeles, J.: Singularity analysis of closed-loop kinematic chains. IEEE Trans. Robot. Autom. 6(3), 281–290 (1990)
Yoshikawa, T.: Manipulability of robotic mechanisms. Int. J. Robot. Res. 4(2), 3–9 (1985)
Zhang, P., Yao, Z., Du, Z.: Global performance index system for kinematic optimization of robotic mechanism. Contributed by the Mechanisms and Robotics Committee of ASME for Publication in the Journal of Mechanical Design
Author information
Authors and Affiliations
Corresponding author
Editor information
Editors and Affiliations
Rights and permissions
Copyright information
© 2018 Springer International Publishing AG
About this paper
Cite this paper
Salem, A.A., Khedr, T.Y., Ghazaly, G.E., Mahmoud, M.I. (2018). Modeling and Performance Analysis of Planar Parallel Manipulators. In: Hassanien, A., Shaalan, K., Gaber, T., Tolba, M. (eds) Proceedings of the International Conference on Advanced Intelligent Systems and Informatics 2017. AISI 2017. Advances in Intelligent Systems and Computing, vol 639. Springer, Cham. https://doi.org/10.1007/978-3-319-64861-3_2
Download citation
DOI: https://doi.org/10.1007/978-3-319-64861-3_2
Published:
Publisher Name: Springer, Cham
Print ISBN: 978-3-319-64860-6
Online ISBN: 978-3-319-64861-3
eBook Packages: EngineeringEngineering (R0)