Skip to main content
SpringerLink
Log in

Ultra-Fast Cooling of Flat Metal Pate in a Modified Runout Table

  • Conference paper
  • First Online:
Advances in Fluid and Thermal Engineering

Part of the book series: Lecture Notes in Mechanical Engineering ((LNME))

Abstract

Cooling of metal components at the end of the steel production process is a highly critical step in production. The cooling process rate is time critical, and it helps determine various crucial steel properties. There is continuing research which is being done to help improve the process to boost the quality of steel produced as well as reduce the overall cost of production. Ultra-fast cooling involves the use of varied water and air pressures as the cooling media. Surface heat flux at each experimental condition was computed from the transient temperature history measured by K-type thermocouples embedded at the bottom surface of the plate. Peak heat flux on the surface of 2.954 MW/m2 was obtained using an inlet pressure of water 5 bar, pressure of air 3 bar, strip velocity of 5 cm/s, and nozzle to plate height of 100 mm for a starting temperature of 1123 K of the 4-mm-thick steel plate.

This is a preview of subscription content, log in via an institution to check access.

Access this chapter

Log in via an institution
Chapter
USD 29.95
Price excludes VAT (USA)
  • Available as PDF
  • Read on any device
  • Instant download
  • Own it forever
eBook
USD 129.00
Price excludes VAT (USA)
  • Available as EPUB and PDF
  • Read on any device
  • Instant download
  • Own it forever
Softcover Book
USD 169.99
Price excludes VAT (USA)
  • Compact, lightweight edition
  • Dispatched in 3 to 5 business days
  • Free shipping worldwide - see info
Hardcover Book
USD 169.99
Price excludes VAT (USA)
  • Durable hardcover edition
  • Dispatched in 3 to 5 business days
  • Free shipping worldwide - see info

Tax calculation will be finalised at checkout

Purchases are for personal use only

Institutional subscriptions

References

  1. Challa VSA, Zhou WH, Misra RDK, O’Malley R, Jansto SG (2014) The effect of coiling temperature on the microstructure and mechanical properties of a niobium-titanium microalloyed steel processed via thin slab casting. Mater Sci Eng, A 595:143–153

    Article  Google Scholar 

  2. Biss V, Cryderman RL (1971) Martensite and retained austenite in hot-rolled, low-carbon bainitic steels. Metall Mater Trans B 2(8):2267–2276

    Article  Google Scholar 

  3. Elmay W et al (2013) Effects of thermomechanical process on the microstructure and mechanical properties of a fully martensitic titanium-based biomedical alloy. J Mech Behav Biomed Mater 18:47–56

    Article  Google Scholar 

  4. Nayak SK, Mishra PC, Parashar SKS (2016) Influence of spray characteristics on heat flux in dual phase spray impingement cooling of hot surface. Alexandria Eng J 55(3):1995–2004

    Article  Google Scholar 

  5. Chen SJ, Tseng AA (1992) Spray and jet cooling in steel rolling. Int J Heat Fluid Flow 13(4):358–369

    Article  Google Scholar 

  6. Zhao Y, Huang X, Yu B, Yuan X, Liu X (2017) Effect of coiling temperature on microstructure, properties and resistance to fish-scaling of hot rolled enamel steel. Materials (Basel) 10(9)

    Google Scholar 

  7. Zhang Z, Jiang P-X, Hu Y-T, Li J (2013) Experimental investigation of continual- and intermittent-spray cooling. Exp Heat Transf 26(5):453–469

    Article  Google Scholar 

  8. Lucas A et al (2004) Metallurgical aspects of ultra fast cooling in front of the down-coiler. Steel Res Int 75(2):139–146

    Article  Google Scholar 

  9. Sussman M, Smereka P, Osher S (1994) A level set approach for computing solutions to incompressible two-phase flow. J Comput Phys 114(1):146–159

    Article  Google Scholar 

  10. Amon CH, Murthy J, Yao SC, Narumanchi S, Wu CF, Hsieh CC (2001) MEMS-enabled thermal management of high-heat-flux devices EDIFICE: embedded droplet impingement for integrated cooling of electronics. Exp Therm Fluid Sci 25(5):231–242

    Article  Google Scholar 

  11. Choi KJ, Yao SC (1987) Mechanisms of film boiling heat transfer of normally impacting spray. Int J Heat Mass Transf 30(2):311–318

    Article  Google Scholar 

  12. Pereira RH, Filho EPB, Braga SL, Parise JAR (2013) Nucleate boiling in large arrays of impinging water sprays. Heat Transf Eng 34(5–6):479–491

    Article  Google Scholar 

  13. Aamir M, Qiang L, Xun Z, Hong W, Zubair M (2014) Ultra fast spray cooling and critical droplet diameter estimation from cooling rate. J Power Energy Eng 2:259–270

    Google Scholar 

  14. Mohapatra SS, Ravikumar SV, Ranjan R, Pal SK, Brat Singh S, Chakraborty S (2013) Ultra fast cooling and its effect on the mechanical properties of steel. J Heat Transf 136(3):32101

    Google Scholar 

  15. Somasundaram S, Tay AAO (2013) Comparative study of intermittent spray cooling in single and two phase regimes. Int J Therm Sci 74(C):174–182

    Google Scholar 

  16. Bhattacharya P, Samanta AN, Chakraborty S (2009) Spray evaporative cooling to achieve ultra fast cooling in runout table. Int J Therm Sci 48(9):1741–1747

    Article  Google Scholar 

  17. Selvam RP, Lin L, Ponnappan R (2006) Direct simulation of spray cooling: effect of vapor bubble growth and liquid droplet impact on heat transfer. Int J Heat Mass Transf 49(23–24):4265–4278

    Article  Google Scholar 

  18. Mishra PC, Mukhopadhyay A, Sen S (2014) Experimental investigation of heat transfer characteristics in water shower cooling of steel plate. J Enhanc Heat Transf 21(1)

    Google Scholar 

  19. Taguchi RP (1988) Techniques for quality engineering. McGraw Hill

    Google Scholar 

Download references

Author information

Authors and Affiliations

  1. KIIT, Deemed to be University, Patia, Bhubaneshwar, 751024, Odisha, India

    Sudhansu Mohan Padhy, Purna Chandra Mishra, Ruby Mishra & Achintya Kambli

Authors
  1. Sudhansu Mohan Padhy
    View author publications

    You can also search for this author in PubMed Google Scholar

  2. Purna Chandra Mishra
    View author publications

    You can also search for this author in PubMed Google Scholar

  3. Ruby Mishra
    View author publications

    You can also search for this author in PubMed Google Scholar

  4. Achintya Kambli
    View author publications

    You can also search for this author in PubMed Google Scholar

Corresponding author

Correspondence to Purna Chandra Mishra .

Editor information

Editors and Affiliations

  1. Oak Ridge Institute for Science and Education, Oak Ridge, TN, USA

    Pankaj Saha

  2. Department of Mechanical Engineering, Indian Institute of Technology Delhi, New Delhi, Delhi, India

    P.M.V. Subbarao

  3. Department of Mechanical Engineering, Amity School of Engineering and Technology, Amity University Uttar Pradesh, NOIDA, Uttar Pradesh, India

    Basant Singh Sikarwar

Rights and permissions

Reprints and permissions

Copyright information

© 2019 Springer Nature Singapore Pte Ltd.

About this paper

Check for updates. Verify currency and authenticity via CrossMark

Cite this paper

Padhy, S.M., Mishra, P.C., Mishra, R., Kambli, A. (2019). Ultra-Fast Cooling of Flat Metal Pate in a Modified Runout Table. In: Saha, P., Subbarao, P., Sikarwar, B. (eds) Advances in Fluid and Thermal Engineering. Lecture Notes in Mechanical Engineering. Springer, Singapore. https://doi.org/10.1007/978-981-13-6416-7_22

Download citation

  • DOI: https://doi.org/10.1007/978-981-13-6416-7_22

  • Published:

  • Publisher Name: Springer, Singapore

  • Print ISBN: 978-981-13-6415-0

  • Online ISBN: 978-981-13-6416-7

  • eBook Packages: EngineeringEngineering (R0)

Publish with us

Policies and ethics

Search

Navigation