Surface roughness effect on a magnetic fluid-based squeeze film between a curved porous circular plate and a flat circular plate M. E. ShimpiG. M. Deheri Technical Paper 09 August 2013 Pages: 233 - 243
Heat transfer to Herschel–Bulkley materials flowing in the entrance of tubes with an imposed wall temperature profile Johnny Q. da SilvaEdson J. SoaresRafhael M. Andrade Technical Paper 25 September 2013 Pages: 245 - 255
Optimization of a stochastic dynamical system R. H. LopezT. G. RittoJosé Eduardo Souza de Cursi Technical Paper 08 August 2013 Pages: 257 - 264
Fatigue damage of a drilling tower induced by ocean waves Victor F. D. SacramentoRubens SampaioThiago G. Ritto Technical Paper 25 August 2013 Pages: 265 - 275
Analysis of structural reliability from time response using fully probabilistic Fang YongfengChen JianjunCao Hongjun Technical Paper 23 August 2013 Pages: 277 - 281
Modeling of piezoelectric energy harvesting considering the dependence of the rectifier circuit Marcel Araujo ClementinoRomeu ReginattoSamuel da Silva Technical Paper 29 August 2013 Pages: 283 - 292
Influence of substrate roughness on adhesion of TiN coatings Aleksandar MiletićPal TerekDragan Kukuruzović Technical Paper 11 September 2013 Pages: 293 - 299
Multi-objective process optimization of wire electrical discharge machining based on response surface methodology Danial GhodsiyehAbolfazl GolshanS. Izman Technical Paper 20 August 2013 Pages: 301 - 313
Simulation machining of titanium alloy (Ti-6Al-4V) based on the finite element modeling Moaz H. AliM. N. M. AnsariA. A. Oshkour Technical Paper 22 August 2013 Pages: 315 - 324
Simulation of the hone broaching process with diamond tools Guilherme Evangelista VargasKonrad WegenerRolf Bertrand Schroeter Technical Paper 22 August 2013 Pages: 325 - 333
Wire electrical discharge machining of AA7075/SiC/Al2O3 hybrid composite fabricated by inert gas-assisted electromagnetic stir-casting process Shyam LalSudhir KumarA. N. Siddiquee Technical Paper 22 August 2013 Pages: 335 - 346
Investigation of burr formation and surface roughness in drilling engineering plastics Mihrigul AltanErhan Altan Technical Paper 27 August 2013 Pages: 347 - 354
Modeling of residual stress distribution around fastener holes in thin plates after symmetric cold expansion J. T. MaximovG. V. DunchevaI. M. Amudjev Technical Paper 08 September 2013 Pages: 355 - 369
Influence of friction parameters on springback and bend force in air bending of electrogalvanised steel sheet: an experimental study R. SrinivasanD. VasudevanP. Padmanabhan Technical Paper 08 September 2013 Pages: 371 - 376
Assessment of a transient homogeneous reactor through in situ adaptive tabulation Americo Cunha JrLuís Fernando Figueira da Silva Technical Paper 23 August 2013 Pages: 377 - 391
Thermoanalysis and reaction kinetics of heavy oil combustion Anderson N. PereiraOsvair V. Trevisan Technical Paper 17 September 2013 Pages: 393 - 401
Combustion time of the oxygenated and non-oxygenated fuels in an Otto cycle engine Pedro MelloFabiano WildnerRosângela da Silva Technical Paper Open access 27 October 2013 Pages: 403 - 410
Experimental study of mixing layer in a closed compound channel Jhon GoulartLuciano NoletoSérgio V. Möller Technical Paper 21 August 2013 Pages: 411 - 420
Trap based part feeding system for stacking sector shaped parts S. UdhayakumarP. V. MohanramR. Srinivasan Technical Paper 20 August 2013 Pages: 421 - 431