1. Improving tracking performance of industrial SCARA robots using a new sliding mode control algorithm

   • Min-Cheol Lee
   • Kwon Son
   • Jang-Myoung Lee

   OriginalPaper Pages: 761 - 772

2. An ATHOS3 code model development and fluid-elastic vibration analysis for YGN 3/4 steam generators

   • Ukhwan Sur

   OriginalPaper Pages: 773 - 781

3. Observer-based wheelbase preview control of active vehicle suspensions

   • Hyoun-Surk Roh
   • Youngjin Park

   OriginalPaper Pages: 782 - 791

4. A probabilistic model for the scale effect on fracture toughness of structural ceramics

   • Amkee Kim
   • Seung-Hoon Nahm

   OriginalPaper Pages: 792 - 799

5. Fuzzy logic cross-coupling controller for precision contour machining

   • Sungchul Jee

   OriginalPaper Pages: 800 - 810

6. In-situ running bucket vibration test of an intermediate-pressure steam turbine

   • Jong-Po Park

   OriginalPaper Pages: 811 - 817

7. Small punch tests on steels for steam power plant(I)

   • Jeong Soo Ha
   • Eric Fleury

   OriginalPaper Pages: 818 - 826

8. Small punch tests on steels for steam power plant (II)

   • Eric Fleury
   • Jeong Soo Ha

   OriginalPaper Pages: 827 - 835

9. Effect of modal filter errors on vibration control characteristics

   • Jai-Hyuk Hwang
   • Jung-Soo Kim
   • Joon-Soo Kim

   OriginalPaper Pages: 836 - 846

10. An optimal control model for determining articular contact forces at the human knee during rising from a static squat position

    • Seonpil Kim
    • Marcus G. Pandy

    OriginalPaper Pages: 847 - 858

11. An approximate method to build an improved stress field in local regions

    • Kee-Nam Song

    OriginalPaper Pages: 859 - 870

12. A procedure for the improved continuous stress field of composite media

    • Kee-Nam Song

    OriginalPaper Pages: 871 - 880

13. Vane tip detachment in a positive displacement vane pump

    • Myung-Rae Cho
    • Dong-Chul Han

    OriginalPaper Pages: 881 - 887

14. A bond graph approach to the modeling of general multibody dynamic systems

    • Whang Cho

    OriginalPaper Pages: 888 - 898

15. Swirl effect on the spray characteristics of a twin-fluid jet

    • Byung-Joon Rho
    • Shin-Jae Kang
    • Sam-Goo Lee

    OriginalPaper Pages: 899 - 906

16. On the intermittent spray characteristics

    • Won-Tae Kim
    • Sam-Goo Lee
    • Shin-Jae Kang

    OriginalPaper Pages: 907 - 916

17. Performance of heat transfer and pressure drop in a spirally indented tube

    • Sang Chun Lee
    • Sang Chul Nam
    • Tae Gon Ban

    OriginalPaper Pages: 917 - 925

18. Design of a two-phase loop thermosyphon for telecommunications system (I)

    • Won Tae Kim
    • Kyu Sub Song
    • Young Lee

    OriginalPaper Pages: 926 - 941

19. Design of a two-phase loop thermosyphon for telecommunications system (II)

    • Won Tae Kim
    • Kwang Soo Kim
    • Young Lee

    OriginalPaper Pages: 942 - 955

20. Comparisons of predicted and measured results on performance and emission of engine effected by intake air dilution and supercharging

    • Jae Keun Park
    • Sang Man Lee
    • Jae Ou Chae

    OriginalPaper Pages: 956 - 962

21. A numerical study on flow and heat transfer characteristics of film cooling with a compound angle hole

    • Jung Hee Lee
    • Young Ki Choi

    OriginalPaper Pages: 963 - 971

22. Thermal investigation of an infrared reflow oven with a convection fan

    • Mi Ro Kim
    • Young Ki Choi
    • Jung Hee Lee

    OriginalPaper Pages: 972 - 979

23. Numerical simulation of a pool fire

    • Dong-Eun Lee
    • Seung-Wook Baek

    OriginalPaper Pages: 980 - 987

24. Numerical modeling of heat and mass diffusion in compressible low speed flows

    • Yun-Ho Choi

    OriginalPaper Pages: 988 - 998

25. Parallel computations of 3D flows in resin transfer molding

    • Whie Chang

    OriginalPaper Pages: 999 - 1010